Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
This must be stupid question of the day. I have my nRF51822 kit and my nrfGO kit and I can't find the product key. On the box for the nRF51822 there's one tiny sticker with...
I'm using Maple and custom nrf8001 board... I have the following problems...
I'm usign the library from this topic:
forums.leaflabs.com/topic.php
But as you can guest...
I've managed to get my 85122 dev board set up on parallels on a mac and get 'blinky' uploaded to it using Keil and nrfGO studio. I then changed blinky to do something else...
What is the exact meaning of this error code? Is the pipe busy? The nRF8001? The peer? Is an indication of something I did wrong, or just a indication that something needs...
Hello,
finally I am developing an application for iPhone which works together with the nRF8001/nRF8002 which I was able to buy in a reasonable housing already. Therefor I...
First, I'm just beginning bluetooth solutions, so I apologize if my question is dumb :)
I have 2 Arduino boards, with 2 nRF8001 shields.
I want to connect them. After...
Chip: NRF51822
Per the documentation the band gap voltage is 1.2V however on my board when I apply the voltage 1.5V to AIN2 i read the following value from the ADC: 209...
I am completing a schematic using the nRF51822 part. I will be supplying the part with a 3.3V supply. I will use one of the ADC inputs to sense battery voltage (up to 10v...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I was using nRF Master Controller app on Samsung S4 to connect to my Ble device. However, after connected a while, the device will be disconnected automatically while I was...
I'm getting started and have an overwhelming amount of stuff downloaded which I'm trying to make sense of.
Which of the examples in the nrf51 SDK use the Softdevice and...
Hi,
I'm using a NRF8001 shield with an Arduino Leonardo, everything connection wise seems to be working. I'm using the "ble_my_project_template" and uploading various services...
I install the j link driver for mac(4.78k),connect the ek,but can't recognition it:
Sens-Macbook:~ sen$ JLinkExe -if SWD -device nRF51822
SEGGER J-Link Commander V4.78k...
I'm usually cleaning out the older manuals when downloading new ones from the web site. Unfortunately the new EK user guide 1.2 doesn't show how to connect the nrf51822 UART...
