I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hi.
Using 51822 with BLE stack, I was faced with the problem of low transfer rates (5kb) on my android device (phone). It is very slow.
Can work 51822 with standart...
Can I initial like below to generate 2 opposition PWM waves on 2Pins？
/* Configure PPI channel 0 to toggle PWM_OUTPUT_PIN on every Timer 2 COMPARE[0] match. */
NRF_PPI...
Hi All,
Now I'm doing the OTA and I can use the nRF51822 DK and Master Control Pannel to complete the firmware update.I have a idear but I meet some problem.
I use the...
Hi,
Is it possible to update the firmware through usb? i have a nrf51822 evaluation kit, and i also tested the firmware update over ble. Now, i need to update the firmware...
HI Everybody,
I am developing firmware for handling multiple ANT+ Sensors. i am able to collect data from 3 different sensors, but in below scenario am getting channel...
Hi,
This may be a silly question but I'm trying to generate two timed interrupt events using only TIMER0 (the MCU is nrf51822). My code is:
#define TIMEOUT1 3000 ...
I am beginner on this platform. I was hoping for KEIl IDE to aid my development, but since license fee is more, i wanted to try GCC platform. But unable to set it up. In nAN...
Hello,
We are developing an application that has to be able to send the data of a VGA image, and We don't know which of the GATT supported profiles will be the best to...
Hi,
I'm using SDK 4.4.2 and softdevice 5.2.1 to try the HID example. Although it is provided for the nRF6350 kit, I ported (buttons and LEDs) the example to the EV kit...
Hi,
I've been using your nRF51822 with considerable success. I now need to migrate across to an M3 for greater power. I want to keep most of the application code I wrote...
Hi
Thank you for the IOS App "nRF Loader" which was released last week. It works well and offers a lot of possibilities for Nordic developpers. I've one question about...
Hi,
I have just opened my nRF8001 DK. It seems like for the evaluation of the nRF8001, I also need to purchase a nRFgo Motherboard, which is sold separetely.
Where does...
Hello,
I would like to do some code tests and simulations of my application in the keil microvision, so I would like to know if you could give me an example project to...
Is it possible to initiate communicate with an ANT+ device using a nRF24L01+?
I understand that the RF Channel is 2.466 GHz (66), however I do not know what Address(es...
