Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Now，I use a 1s timer to calculate the clock.
At first,I use the telephone to adjust the time to fit the telephone time.
but finally(after a night ) the result runs fastly...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I'm trying to get a UART example running on the nRF51822 mbed kit. However, flashing any uart examples from the SDK onto the board generates a fail.txt file
What is the...
Hi, i build my own custom board with a NRF52832, i'm having problem with the softdevice (i think so)... my code is base on BLE s132 central and peripheral...
I developed...
I'm using PCA10028 board.
I copied hex file of ble_app_uart project to this board. And then I scanned via my device - Galaxy Note 5, cutting edge phone.
But I couldn't find...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am trying to achieve the maximum throughput when using the nRF51822.
According to the answer in this link ( devzone.nordicsemi.com/.../) , operation mode (write...
Hi,
I have a beacon Kit PCA20006. I have programmed it with
SOFTDEVICE
C:/Users/Arsalan/Desktop/Engineering/Devices/nRF51822/SDK/sdk11/components/softdevice...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0 . I try to modify the example code let it can connect the Environmental Sensing...
I have implemented static passkey onto ble_app_uart.
I would like to configure this passkey through uart, then store it in the flash. I am confused at the choices available...
Hi, I'm having some trouble connecting to the nrf51822 chip and I've tried connecting to it using master controller, nrf connect, and nrf toolbox. The chip isn't even appearing...
Hi,
I'm working on NRF52 NFC and I meet an issue related to timing.
I'm using hal_nfc_t2t driver directly (Without nfc lib) because I want to do some custom work and I...
Hello !
I am trying to read WHO_AM_I register from a LSM9DS1 IMU.
I have spi_update_imu_data() as my callback for when the spi transfer completes and inside it I make spi_xfer_done...
