Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hello,
I've been trying to figure out if this board with STM32F103 ( www.aliexpress.com/.../2042650923.html
can directly plug into my debug board
( www.aliexpress...
All,
We are in product on a product using the nRF52832 and are noticing in manufacturing that we aren't able to make it through the self test part of fab because of shoddy...
I need to understand how a multi-link configuration can achieve real-time transmission - its all about latency.
The Application
In my nRF52840 application I have several...
Hello,
I am using a custom bootloader. The bootloader does not contain dfu, it will just check the new image, program the new image, then jump to it.
I cannot jump to...
Hi,
I want my characteristic to have a different UUID than its service on my server:
I followed the leads from the post below:
https://devzone.nordicsemi.com/f...
Hi there
I was following all the steps on Building the mesh stack and examples , Building with SEGGER Embedded Studio and nRF5 SDK for Mesh Segger Embedded Studio first...
Hello
My understanding is that the only way a mobile phone can communicate with a mesh network is through the GATT bearer..
Im trying to figure out why its not possible...
Im using two nrf51822 as severs and one nrf52DK as a client in mesh light-switch examples. So i need to implement mesh dfu on server side( on nrf51822) . How to do this ....
Dear Support,
Installed the new Mesh SDK v2.1.0 and tried to build the sample solutions with SES.
Unfortunately I am always getting the following error:
build/serial_nrf52832_xxAA_s132_6...
I would like to use both UARTs.
I'm trying to run the given example with SDK patch from https://devzone.nordicsemi.com/f/nordic-q-a/25173/nrf52840-uart1-not-working-in-sdk...
Goodmornig,
I can't compiling the example project ! Do you knows the reason ?
Error ( imagw1 ): C:\Users\utente\Desktop\pc-nrfconnect-rssi-master\fw\src\rssi_uart\sdk...
Hello everyone, I'm trying to run my nrf51 with ADS1298 using SPI. nrf51 is master and ADS1298 is slave.
I configured SPI as
const nrf_drv_spi_config_t spi_config =...
Hi,
I'm trying to implement GPIOs in Mesh 2.0 light switch example and I'm using SDK 15.0. I'm getting undefined reference errors and I know that I have to add legacy GPIOTE...
Hello guys.
I'm new with nodic nRF52 SDK and I tried to enable debug by setting 1 on "NRF_LOG_ENABLED" in sdk_config.h, but nothing happens in com port criated by Jtag...
