I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello,
We are developing wearable which has NRF52 as main MCU. We are looking for suggestions to select proper sensors like Pedometer, Heart Rate Sensor and 128x32 OLED...
Device：Nrf51822
SDK：SDK12.3
Device name consists of "scanner:" and four digits。But sometimes the device name display error。An extra character appears in the device name...
Hi,
I've undertaken my very first custom Bluetooth PCB project, choosing an nRF52810 as the MCU of choice.
Having already tried and tested a SparkFun nRF52832 breakout...
Hi all!
Antenna that used in nRf51822 developement kit:
too big for my design, so I tried to use antenna that I copied from TI AN430:
There is devices that use...
Hi,
I am following procedure to configure mosquitto using this link http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fiot_sdk_user_guides_mosquitto...
Hello,
I'm working in a bootloader based on the one included with SDK15. I want to add a timer that fires every 50 ms to keep track of time. The purpose of this timer is...
Hello everyone,
I'm new to embedded system and I'm working with the NRF52 and more precisely with the DW1001 (NRF52 + DW1000).
The Decawave device (DW1000) is already...
Hello,
I am trying to run a simple ble_app_hrs example from the SDK v12, but I am getting the same error as in this post devzone.nordicsemi.com/.../
Building ‘ble_app_hrs_pca10040_s132...
Hi,
UART and UARTE are specified in data sheet. these are separate UART or one UART and configured bt software. Please explain.
Thanks and Regards,
Harikant
So literally, I cannot trust what IAR is doing. Running version 8.22.1, it crashes every time I attempt to debug an nRF52832 device (SparkFun board).
I've already programmed...
i'm using uart for debugging, works fine and dandy except when in app_error_handler.
There only the first character is being printed before we go into an infinite loop. Inside...
Hello,
My custom board is based on an accelerometer which sends interrupts to nrf52832 to Sleep and Wake-up (pins GPIOTE).
(The FW is based on SDK15\examples\ble_peripheral...
Hi!
I am using SDK15.
I am using ble_app_uart and let's suppose that both of my characteristics (RX and TX) have char_md.char_props.write = 1; property so I am able to...
Hello everyone,
I'm looking the power profile of the advertising event for the S140 stack but two points trouble me.
• Why the module advertises 3 times ? One of the new...
i want NRF_UICR->CUSTOMER register to save MAC address and SN code.
mobile phone transport the fix mac address and SN code to the nrf52832.
it is looks like that it can...
