Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I have and older board which is the PCA10028 with the nRF51422 chip.
I have downloaded the nRF5 SKD 15.0.0 and found there is not example DFU project for my particular board...
Hello
I am working on a project based on the Mesh SDK 2.0.1 light_switch example. The system is using SD 6.0.0 and PCA10040 boards. DFU is successfully implemented on the...
Hi,
I work on nrf52832 with the serialization.
The nrf52832 connectivity part is load with S132 V6.0.0 (uart hci).
The stm32 will communicate with the 52832 throught...
Hello, can you say me:
1) which Stack parts in Mesh SDK: nrf5_SDK_for_Mesh_v2.0.1 are implemented in harmony with Bluetooth Mesh Profile Specification and which are not...
Hi,
We are attempting to send data via BLE every 100 ms using an app_timer. The app_timer sets a flag and in the while loop in main.c we call
ret_code_t err_code; do ...
Hello, i'm currently doing my own DFU central for the BLE DFU on SDK 13, i followed all the steps on this link , i created the init and image files with nrfutil and now i...
I am trying to connect my Ubuntu machine with my nrf52 custom board my setup is as follows, Ubuntu machine --> FTDI USB2UART --> HCI interface of nrf52 I can see on my logic...
My application (nRF51 S130 v2.0.1 SDK12.3.0) uses the Radio Timeslot feature for multiprotocol support similarly to the example in https://github.com/NordicPlayground/nrf51...
am trying to synchronize two nrf52840 thank's to state gpio with gpiote function but it return an error code 4 (No Memory for operation) whith this line -> NRF_LOG_INFO("no...
Hi Nordic Team,
What I want to achieve is to add a service with a custom 128-bit UUID that has about 4 characteristics with a completely different 128-bit UUIDs that are...
Hi Nordic,
I'm using NRF52832 to design a producation that needs four SPI interfaces.
The four spi peripherals are: gSensor, LCD, SPI Nor Flash, and PPG Sensor. Now...
Hi,
I'm working on a custom board with the nrf52840 engineering version n52840QIAABB with de SDK15. I've tried the exemple usbd_ble_uart from the SDK15 and it works well...
Figure 1. Data encoded and sent (attached)
Figure 2. Screen shot of wrong Time data (attached)
Here is some code that seems to be correct, sending 10 bytes that look...
Hi ,
I want to know how to give passkey to nrf8001 peripheral mode if it dont have display/keyboard/button, I have hear about justworks but not sure how it will work. Could...
Hello,
I am was playing around a bit with the twi_scanner-example and I figured out, that no matter if I chose the legacy-layer with nrf_drv_twi-functions or the new nrfx_twi...
