Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
We have the samples of the NRF52 in CSP, but we don't find the documentation concerning the pin assignments.
We would like to do a routing with this chip, is it...
I am trying to incorporate our Manufacturer name to the Device Information Service. I am working on the ble_app_uart example which does not include the file ble_dis.c nor...
Hi Mate,
When I test the example of ANT which is named as hrm_tx(heart rate transmitter), after I programed the ANT_s212_nrf52_0.5.1.alpha.hex and the application of hrm_tx...
I'm running a BLE application on the nRF51822. And I have an application timer to keep track of the real time clock. However, when I receive a BLE_GAP_EVT_DISCONNECTED event...
When i load a nRF52 example in Keil µVision 5.17 (for example ble_app_proximity_s132_pca10040)
The i get a indication that the Configuration files are not compatible
I am...
Hi,
I have a strange problem，
I use NUS service connect with phone , send or receive data，after some process，may happen
the keyboard(use GPIOE interrupt) has no response...
I am trying to test the ble_lbs example to understand the basic working principle of the ble custom service using NAN_36 document after compilation followed by the procedure...
Hi,
I am running the sample glucose app on the nordic chip.
On the iOS we have nRF Toolbox.
iOS Version is 8.3.
SDK version of sample glucose is 10.
After sometime...
Hello,
I've made a hardware base on new nrf52. I followed the exact schematic of eval board and requirements.
Clocks seem to be good (32KHz and 32MHz).
A mange to mkae...
hi ,
i want to transfer data using custom profile.
in which i want to have apple midi uuid service (03B80E5A-EDE8-4B33-A751-6CE34EC4C700) and IO characterstics (7772E5DB...
Hi.
I want to change device name to identify multiple devices.
When I am using two device, the initial device name is "device".
If I connect these two device to iphone...
I have an application that needs to minimize its current consumption when sleeping. From the nRF52 manual, I see that UART should consume 1uA when in idle. The total current...
Hello,
I'm using thhe BLE shied, which uses the nRF8001 chip, with arduino Mega.
I'm trying to connect the Rf module nRF24l01 to receive data from another arduino and...
When checking if a read (or write) is authorized can the event contain an invalid handle (Does the handle need to be checked)?
case BLE_GATTS_AUTHORIZE_TYPE_READ:
{
...
hi
in nrf51422
till now this is my code
now how can i send or recieve information .
or tell me for sending information what to read next?
#include <stdint.h>
#include...
