Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
Hi,
I am trying to build bluetooth hci_uart sample for esp32 board and haven't had much success so far. I am running this command to build:
`west build -p always -b...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原ĺ›
uint32_t...
I'm running into something weird on SDK8.0 (I will be upgrading soon to SDK10, however it's a layered roll out so I can't update right now unless you tell me it's a bug in...
I was trying to view the scan response packet using the master control panel app I have on my android phone, but I can't seem to see where it is.
I want to update the scan...
I'm looking at an application where it would be beneficial to be able to read data from the bluetooth device as it passes. It would be easiest for me to do this by simply...
I am using the TWI module in master mode, with sdk 10. I purposely create an error situation, in which the TWI gets stuck and keeps returning NRF_ERROR_BUSY every time I try...
I've completed the Custom service tutorial, and I wanted to port the system to use the SDK10 with the pack installer. I've run into an issue though.
The code runs fine...
Are the GPIO pins in disconnected state during the startup until they are configured by the Firmware?
If not what is the state of the GPIO pins during startup?
Hello.
I have problems uploading with DFU OTA any application. For this case, I am using "dual_bank_ble_s310" example.
First of all, I put this memory's configuration...
Hi,
I am using nrf51822 CDAB version chip which has 128kb of flash memory, my code is built on ble_hrs
I am trying to save my app_trace logs i.e., redirecting my printf...
Hi,
I'm using pca10040 board. For my requirement i'm using FreeRTOS. While creating task we need to set stack size for each task.
For that i created only one task with...
Hello,
i would like to scan for a custom UUID Ventor. And when the BLE Central found this BLE Client.
I will Change one Output pin from low to high.
I start with the...
hi,
after connecting to peripheral device. app_timer_cnt_get() function always gives 0. why it is so. i am not able to understand it.
can anyone help me to get the current...
Hi all,
Can I do something like this:
The SPI master sets CSN line low.
The SPI master sends multiple packets. And the total number of bytes exceeds the...
I want to transfer data collected in my nrf52DK to nRF51 dongle at regular intervals. Right now I can use master control panel in PC to receive the data. Is there any way...
I am using the bootloader from github here to upload DFU over-the-air using an android phone. It works fine for bootloader and application uploads. But if I upload the softdevice...
I'm looking for a radio module for a harsh environment (steelworks furnace)
The module has to work at high temperature 80°C and must transmit 16bytes every second at a distance...
