Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi,
we are using a nRF51822 built into an industrial sensor device. As part of the final production test we want to check the RF connection between the BLE chip and a test...
Hi,
I have a central device and I need to register lot of 128 bit vendor service/characteristics (~20).
However, sd_ble_uuid_vs_add return NRF_ERROR_NO_MEM.
Some post...
HI , Global Tech Tour 2015 - Shenzhen I get the infomation that the R&D in nordic Semiconductor has got the development board NRF52 smart remote. What's the data you will...
Hi All, I'm trying to compile and download sample code "dual_bank_ble_s130".
But it seems fail to run.
I'm using SDK10 examples\dfu\bootloader\pca10028\dual_bank_ble_s130...
can we transmit data of size greater than 40kb (image) through nrf51822 but without connection to peripheral device i am working so hard to find a way but not achieving the...
Hi I'm trying to optimize my connection interval for latency vs power consumption but I notice that a lot of values I try to set are giving me the invalid parameter error...
Hello,
I am using S120 central stack 2.1.0 with SDK 9.0 and able to work with single server connection. Now I am trying to connect to 2 peripherals with 2 different UUID...
I read timer example of SDK7.0/6.0, and found that often we write some code to tigger the clock.
but the same example of SDK9.0 needn't. why ?
the code of SDK7.0: NRF_CLOCK...
Hi,
I am developing ble apps with the BL600.
I am coding a source file with the keil IDE. And this source is deployed to the nRF51 DK board through the nRFgo Studio....
hello,
i am unable to update application or softdevice or bootloader via master control panel 3.9.0
while doing so, it shows error:"FAILED TO OPEN TRANPORT BACKEND". ...
I followed the Nordic Tutorial located here . I'm using a PCA100028 Dev Board, MCP 3.9.0.6, and a Segger J-Link Plus. I'm using Keil uVision5, and used the pack installer...
I have a set of characteristics on my ble peripheral (nrf51) which I display with nordic control panel tool (android). but when I deleted one characteristic on the peripheral...
Hi, I am evaluating the use of Gazell and BLE as a possible solution for my project. I had heard that there was a way to have both BLE and Gazell running on a device at the...
we will do some measurments and answer when we get some time to spare for this. Others are welcome to answer/comment freely about their experiences/knowledge.
I have some custom hardware (nRF51822) with a couple sensors on it and would like to have the data sent via BLE to a smartphone. This may be timer based on triggered by an...
