Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
Developing on the nrf51822
Have working code for the nRF52840 Dongle using the pc-ble-driver therefore all Bluetooth work is done using sd_* calls. The PC provides easy...
I have one of the new Power Profiler Kits, and it works really well (well done!). The only problem is I can't reprogram the dev kit while it is connected to the Power Profiler...
I have tried to build this by double-click on the .xcworkspace file, in the folder obtained from the downloaded .zip (dated Nov 24, 2016), then "Build + Run". I get 203 errors...
I have modified the template's code so ble_advertising_init should setup manufacturer data, once I have this assignment:
advdata.p_manuf_specific_data = &manuf_data;
...
Hi,
I want to use nRF51422 on ant and ble dual mode.
Does nRF51422 can use sd332 and where has example project
or
The nRF51422 just can use Sd310 only so far.
Than...
Hello,
When line 10 of the below code is executed the system enters the BusFault_Handler, at this point the NVMC register is as followed: Ready = 0x00000001, Config = 0x00000001...
Hello ! I am using Red Bear Nano which has nrf51822 and I have connected it to a computer with linux. On the computer I downloaded arm-gcc version 4_9 and I linked it to the...
hi all!
if I restarting advertising with BLE_GAP_ADV_TYPE_ADV_NONCONN_IND during CONNECTION occur sd_ble_gap_adv_start(..) returns error = 0x07 ( NRF_ERROR_INVALID_PARAM...
Hi,
Would I be able to get more information on the statement below from the nrf52832 datasheet?
"A step increase in supply voltage of 300 mV or more, with rise time of...
As an example, let's see this function from app_hrm (heart rate monitor):
static void conn_params_init(void)
{
uint32_t err_code;
ble_conn_params_init_t cp_init;
...
I am laying out a board in altium using the nRF51422 - just cutting out the essential pieces in the silk box from the nRF51 DK altium project.
I have some concerns. Once...
Hello, I am going to make a PCB to mount the module and programming pins SWCLK/SWDIO/VCC/GND. I wanted to run my module at 1.8v, but I am worried if the nRF51 dev board, when...
[87] CPU: Unexpected wake from System ON Idle when using FPU
This anomaly applies to IC Rev. Rev 1, build codes QFAA-B00, QFAB-B00, CIAA-B00.
I have the PCA10040....
I made a custom board with the nRF52+SDK11.0.0+s132. The firmware is based on the ble_hrs example (modified to fit my board and modified the application, but the basic premise...
I want to change Variable state( 0->1 or 1->0) when I push the button.
I was searching for example relating to the GPIO.
but I did not find that i want.
Everything...
