I've been trying to flash an nRF52840-DK with code that successfully builds on Segger. The Segger error is "Failed to connect to target." I updated the devkit firmware with...
I am trying to set up a w25q128 using SPI with a nrf5340 on a custom board and had a few questions. I have used DevAcademy as a reference as I do eventually want to set up...
I have a custom board with nRF52840. It draws power over USB and the data lines are connected as well
USB is defined as follows in the dts
cdc_acm_uart0: cdc_acm_uart0...
Im tring to generate sbom in html or spdx format yousing west ncs-sbom -d build i got this error: package.name += '-' + package.version TypeError: unsupported operand type...
Hi there, I'm facing difficulties configuring the Adafruit ILI9341 with the nRF52840. Are there any beginner-friendly instructions on how to configure and program it over...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hey Team,
I'm trying to flash the audio application on our custom PCB, this PCB follows the interfaces of the nrf5340 audio dk. Previously on lower SDK versions (2.7-2.9...
HI,
Nordic part used is nRF51822.
Is there any way to increase signal strength of BLE tx?
I see some parameters in advertising_init function for advdata.p_tx_power_level...
Hi all
According to chapter 50.2 of the nRF52832 product specification V1.2, the pins used for the UART peripheral should be configured before in the GPIO peripheral to...
why most of the examples of sdk 12's sdk config file has different options?
I'm trying to build an application that has Central and Peripheral Role application (and it...
Hi,
I have noticed the new preview DK for NRF82840 is now available, and the new chip is running the new BLE5 spec. My understanding on the BLE v5 is the higher data rate...
Dear Team,
We are facing an issue in nrf51822. We are compiling same project on different system in log file we got certain differences such as
System Licence
...
How to change Peripheral Role to Central Role without having concurrent Role?
I know S130 Can have 8 Concurrent Role as Central, Peripheral, Observer, Broadcaster.
But...
Hellow i am starting with nrf51, and reading nAN-36_v1.1x.pdf doucument
about using use a button to sent a signal through ble.
the BLE hellow world.
but I cant find the...
I'm trying to program 500 raw (not populated on boards) Taiyo Yuden EYSGJNZWY modules, which uses the nRF51882 chipset.
Does anybody know where I can get a fixture to do...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
Long story short, I need to create a packed struct.
I knew the pragma way, to change aligment, didn't work.
I looked up and found the __packed (I'm using Keil µVision...
Hi,
I am planning two have the following network:
1 central communicating with 3 peripherals
One of the peripherals will be a smart device (iOS or Android). What...
Using SDK 12.2, I have compiled the secure bootloader successfully, tweaking the sdk_config and Makefile to use RTT for logging and turning on logging, and using the "_debug...
Configuration: Nordic PPK, PCA10040, PC10028 & PCA63511. Current consumption is relatively high on nRF52 vs nRF51; nRF51 is configured with SDK 10.0 and nRF52 with SDK 12...
Hi,
I have got my nRF52 DK. I could flash softdevice using nrfjprog.
But after reading s132 specification, i have following doubts.
How to flash application from the...
