I am relatively new to embedded and am wondering if there was a "best practices" guide / checklist for production deployment somewhere. Things like making sure you are using...
Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
I implement a card emulation and the card itself doesn't conform to 14443A-3 crc check. I need to disable crc check on card selected event
NRF_NFCT->RXD.FRAMECONFIG...
I've been running a hand soldered prototype board for about a week in an outdoor location where it gets hot and cold (mainly hot), and I noticed it was no longer visible on...
I am trying to add the spi and twi drivers to the ble_app_template project, but I keep running into errors. I am using the SDK 12.2.0. How are we supposed to go about adding...
Problem:
In our project we have one peripheral which can be bonded to many phones at the same time (of cause) while they are still close to it, thus connected via OS. ...
I am trying to scan and connect to a Polar H7 HR belt (which I can do), with m_scan_mode = BLE_NO_SCAN. Once this happens, I understand they are supposed to bond, and at that...
In my low-power application I need to use advertising interval of few seconds (two or more) in order to get lifetime of a year with CR2450 battery. However, the Android application...
There's a great application nRF UART 2.0 that can be used like a terminal with a Bluetooth LE device implementing the "Nordic UART" service. Now I would like to store output...
I am using a nrf52832 with SDK 11.0.0 and sd132. I need to add in-flash storage to my application so I'm looking at the NVMEM documentation and the pstorage module. I understand...
Dear Sir/ Madam,
I want your suggestions and recommendation regarding to choose which one of your BLE development kit.
I want a Bluetooth development kit which has long...
Hello, I'm trying to update services list on central device after adding a new service. However, sd_ble_gatts_service_changed returns NRF_ERROR_NOT_SUPPORTED . After looking...
Hello,
In my application, I need to activate BLE during startup only if some conditions are met otherwise I put the nRF52 in SystemOff mode. BLE should not be activated...
Hi,
I have been receiving the error: undeclared identifier "TWI0_USE_EASY_DMA". I researched and found that the solution was to include "nrf_drv_config.h" and add #define...
Hi, I have problem with discover services in advertising mode on NRF51822-BEACON. There is default firmware in this beacon. I using Xamarin on Visual Studio 2015. It is connected...
I have integrated IAR code into my company system.
with the Jlink_monitor.c, jlink_monitor.h , jlink_monitor_ISR_ISR.s and enableMonitorMode.mac.
Step 1: I loaded code...
Hi,
I am trying to use the nrf_drv_twi class but I cannot define a nrf_drv_twi_t instance. When I write the code
`nrf_drv_twi_t twi = NRF_DRV_TWI_INSTANCE(0);
I get...
