Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
در دنیای پررقابت صنعت غذا، موفقیت رستورانها، هتلها، تالارها و آشپزخانههای مرکزی وابستگی زیادی به کیفیت و کارایی تجهیزات آشپزخانه صنعتی دارد. برخلاف آشپزخانههای خانگی،...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Lets assume i have 3 hex files:
softdevice.hex (addresses 0x0 to 0x1f000)
mySoft1.hex (addresses 0x1f000 to (0x1f000 + size of my program) and 0x7ff00 to...
Currently i am creating the ibeacon app for nRF52. App is able to display UUID, Major and Minor number of surrounding beacons. But is there any way to change the major and...
I have connected (BLE shield + Arduino Mega) with uploaded some Excercises code, It's working for 30 minutes with paired android device and disconnecting automatically.
...
Hello everybody!
I have a problem with compilers for nRF51822.
My problems: I create a pwm signal ~38Khz, duty 30% at pin 30 of nRF51822. This process is work well. I...
hi i m using nrf52 with a pi and the gatttool. pi as master and nrf52 as slave. i want to change the mtu but i got no answer from the nrf52 as you see in the log! do i have...
Hello, I have project to do, but I have too less knowledge about NRF's, I've tried almost all information sources and libraries, but no results. I have to make, that one PIC...
I lost many time and check 3 examples for various versions SDK, in all cases device can t connect to smartphone. Check with appl. "nRF UART 2.0" and last "nRF Connect". Applications...
I've spent the better part of a day trying to get the UART demo to work and I'm not having a lot of success. I did get it to connect and transmit data once - I think that...
Just noticed through some experimentation that the SD 7.1 Stack rejects Non-Connectable Advertising Parameters if the interval is less than 152.5msec? Error: NRF_ERROR_INVALID_PARAM...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
I am developing a wireless sensor network to exchange body movement acceleration data with one Master and several Slaves. In the developing phase I am using the...
Why would sd_ble_gatts_characteristic_add() suddenly return NRF_ERROR_NOT_SUPPORTED?
It is not a documented return.
It happens only when adding a device information...
