Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
Hi ,
I am trying to interface SD card with nrf52. For this I am using fatfs example of new 12.0 sdk. I can able to write the data to file but when I am taking the data...
HI,
I followed this link github.com/.../nRF51-ble-bcast-mesh to develop mesh in nRF51822 dongles. i am able to flash the code( nRF51-ble-bcast-mesh/nRF51/examples/BLE_Gateway...
Hello, I am working on characteristics tutorial.(our service.c)
And I succeeded in notifying characteristic from nordic to android.
The methods I used to notify characteristic...
I'm in the process of migrating to SDK 12.2 and I noticed that nfu_dfu_settings.c now includes app_scheduler.h and makes a call to app_schedule_execute().
How do I use...
want to send a float as a value of a characteristic
I have successfully achieved this using the simple way
Below is the example of just two float variables in an array...
Hi,
I have a PCB with a nRF51822 QFAC A1 onboard, and I wrote a firmware with mbed for this PCB in which P0.08 is supposed to be set to 1 during the initialization and...
My company is in the final stages of prototyping and we want to release our first product in the coming year (focusing on European and American markets). The next steps are...
