Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hello everyone, I'm Dario.
I'm trying to work with a ble nano with nordic component. My target is to receive a string via serial periferial and sending it via bluetooth as...
I am a new engineer working with nRF52 and SDK 12 using Makefile project and arm-gcc. I wrote some simple code to try TWI Master and control a i2c slave device. My question...
Hello I just bought
SKYLAB bluetooth accelerometer sensor SKB360 bluetooth low energy nrf51822 bluetooth 4.0 low energy module
skylab.en.alibaba.com/.../SKYLAB_bluetooth_accelerometer_sensor_SKB360_bluetooth_low_energy_nrf51822_module_bluetooth_4_0_low_energy_module...
Hi,
Im trying to wake up from SYSTEM OFF using LPCOMP.
Im using the following code to power off:
nrf_drv_lpcomp_config_t config = NRF_DRV_LPCONF_DEFAULT_CONFIG;
...
Hi,
I am working on a Beacon application based on nRF52 DK and Eddystone protocol. So i am searching if there is already some examples/SDKs from nRF which supports both...
Looking for document or u tube to program nrf52832 using tag connect (6pin noleg) and nrf52 DK. Have the hex program and put it on the nrf582 dk. need to take to the next...
We have identified a possible transient fault condition in which a voltage in excess of VDD can be applied to an I/O of the nRF51. VDD is 3 V and the excess voltage would...
sdk_resources.h does not compile with c++ in SDK12.
The _cplusplus guard only begins if ESB_PRESENT is defined. The guard should either be moved above or below
#ifdef...
Hi,
do you have any tutorial for contiki on windows based.
no matter which platform you are using.
i am using the ecilpse with cygwin toolchain in ecilpse.
i follow...
Hi,
I'm trying to compare current consumed for different sets of commands mainly with floating point operations in them. As they execute fast, I'm putting them in a loop...
Are there any plans to add write capabilities to the NFC driver? The hardware supports it, but the library provided by Nordic does not (as far as I know). Are there any plans...
I started evaluating the nRF52 using Keil and everything worked great. However, I switched to developing in IAR because I have a full license. I'm using the same code (ble...
Hello Nordic,
I just read the news from may about the arduino primo and i am really exicted!!
I have been tring to decide between arduino due, or some complex ensemble...
I'm developing an application on a custom nRF52 board. I have no problem to program the board with Keil. However when I try to program the application with the nrfjprog, the...
