I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
I have been trying to make the BLE bootloader example works without succes. I am getting stuck after uploading the Softdevices and the Bootloader.
Step by step...
Hello.
I am experimenting examples \ peripherals \ saadc.
It is nrf 52832.
I changed NRF_DRV_TIMER_INSTANCE (0) to NRF_DRV_TIMER_INSTANCE (1), though I tried changing the...
Setting the gatts_enable_params.service_changed to 0 when enabling softdevice removes (or rather doesn't add) the Service Changed characteristic. That's what I want. However...
I'm developing a device based on an nrf52 chipset, and I'm experiencing strange behaving of the Radio interface. The firmware is based on SDK v11 and SoftDevice 132, the hardware...
Line 73 in function nrf_drv_rtc_init snippet bellow checks for UNINIT state. It accesses the m_cb array which is an uninitialized global. That condition would intermittently...
Hi
i buy a nrf51822-02 module and the chip of this,is nrf51822qfaah10
i compile the ble_app_uart_s130 and program my module but it does not have any advertising
my nrfgostudio...
Hello!
Does anyone know how can we send the multiple uint8_t MOSI signal to SPI and received the result on m_rx_buf?
Trying to send multiple bytes to "m_tx_buf":
...
Hi,
It is possible to use an non secure DFU in SDK 12?Like on SDK11?
How to migrate my custom DFU on SDK 11 to SDK 12?
UPDATE 1
it the dfu from sdk 11 I Get an...
When we use nRF5 bootloader provided with SDK the first application flashing must always be done using DFU over-the-air. Only after that it is possible to re-flash application...
Hello,
I'm new to Nordic nRF52 and trying to send commands via termial to nRF52. After receiving commands, nRF52 will use these commands to do i2c communication with other...
Hi,
I'm trying to simply toggle a pin with GPIOTE out toggle task from RTC2 CC0 event. Wrote up the following code and checked the registers in system viewer. Everything...
I am using S132v2 on nrf52831. I am using UART BLE application. I want to turn ON BLE meaning advertising and all parameter of BLE whenever i press any switch. Also bluetooth...
Hi,
I know this question must get asked enough, but i am at my wits end and have not managed to find a solution for this yet.
calling sd_power_system_off returns NRF_INVALID_STATE...
