hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
hi dear Engineers!
if I use sd_ble_gattc_primary_services_discover(..) with NULL last parameter , all SERVICES discovered OK:
start_handle=0x0001;
err_code = sd_ble_gattc_primary_services_discover...
We have a device which needs to survive dishwasher conditions. We believe most dishwashers operate up to 71C, but may reach 82C during 'sanitation' phase/drying.
This is...
Hi,
I'm using nRF5_SDK_12.2.0_f012efa and s132_nrf52_3.0.0_softdevice. We want to do the OTA on it. Before I add a DFU service to make it switch to bootloader, I have use...
Hello, I'm sending a series of data up to 7 bytes from an android phone, but I can only receive the first 5.
I'm asking what are the list of thing to mind if I were trying...
Hi,
I am trying to initiate Firmware Upgrade using the nRF Connect Mobile Application (also tried using nRF ToolBox).
As described in the below link -
github.com/.....
The footprint of sd_ble_gap_connect() is:
uint32_t, sd_ble_gap_connect(ble_gap_addr_t const *p_peer_addr, ble_gap_scan_params_t const *p_scan_params, ble_gap_conn_params_t...
This is what I believe, of course, my beliefs are flawed, so please DO point my errors out:
There is this attribute table on server/peripheral devices. The actual...
Hi，Nordic
I have one nRF24LU1P device, when I make it as USB Dongle, I will use :
hal_usb_endpoint_config(uint8_t ep_num, uint8_t ep_size, hal_usb_cb_endpoint_t endpoint_isr...
When I repeatedly (>290 times) send the same notification to the connected host via sd_ble_gatts_hvx, I get a sd_assertion:
Fault identifier: 0x1
Program counter: 0x104FA...
Hello,
I have a custom board which has NRF52832 SOC(i.e. main MCU) and another ARM Core-M0-based MCU(i.e. target MCU). These two are connected over I2C. I wonder how to...
nRF BLE sniffer is crashing within the first few minutes of use. Attached is the log of one sniffer
session from the start to when it crashes.
Here is my log.txt from...
I'm working my way through BLE Advertising, a beginner's tutorial and getting a SDK error 4001 when trying to use
advdata.include_appearance =
true;
Can anyone...
Hello!
I'm trying to nRF52 soc chip to drive the matrix sensors array (16x16), because there is no enough I/O pins for my project and thinking of use the shift register...
Hello everyone,
I have a program which set configurations by using write (nrf_drv_twi_tx) in the registers of a sensor.
I use the SDK 8 in the nRF51.
Here is the code...
Hello, I want to test using RTT for logging since I am using UART for send/receive packets. I made following changes in sdk_config.h:
#ifndef NRF_LOG_ENABLED
#define NRF_LOG_ENABLED...
