I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
my ble can send data when the data send function called inside main.c ,
But it is not sending data other than in main.c like other source files.. and getting error invalid...
I'm trying out different SDK's and some of them are working to an extent (they load the softdevice, and the app, but when I test run in debug they start at a different location...
I am working with the nRF52832 pca10040 devkit, and when I program the softdevice with the nRFgo studio, the only version that shows the firmware after programming is S132_nRF52_2...
Hi,
we are using nRF51822-QFAA in our project which is based on the PCA10000-nRF51822 Development Dongle 2.0 - layout of radio part is almost the same. I'm also using sdk...
I need to read variable length blocks from an I2C slave using a TXRX transfer. The length of the following data is given in the first read data byte, similar to SMbus Is there...
I installed Bluetooth Developer Studio , (BDS), which appears to offer a way of setting up a custom profile without have to spend too much time on writing low level code....
Dear Everyone.
Hi, I develop nrf51822 with DK PCA10028. I have been optimizing the power consumption to some extent. But now I am very confused.
I use S110 softdevice...
Hello Everyone
We have a project using the Feather 32u4 BLE chip to communicate with an IONIC Application on Android.
And the huge problem is that i'm really really...
Hi,
I am interfacing HX711- 24 bit ADC for Weigh Scale to calculate weight which has
DOUT and PD_SCLK for Digital Output and Digital Input. I have the working Arduino code...
With Eddystone example in SDK12.0.0 I am trying to configure with nRF Beacon for Eddystone application but every time I change the URL " www.nordicsemi.com/" to something...
I use SPI connection according to the table .
I want to press the button 4 on tx (P.06) to transfer "hello", to write down the answer of rx(P.08) in the file on sd card in...
Hi
I'm using nrf51 to notify some data to an andriod device. I set the connection interval of my nrf51 program to 7.5ms. And I need to send 100 packets per second (20 bytes...
Hi Admin.
How can i calculate distance using RSSI. is there any existing method available? i tried statically(like 35-40=1m 40-45=2m) but i dont know actual method to get...
Hi all,
I am trying to add the iOSDFULibrary library to an existing Objective-c project via Cocoapods (Xcode 8.2.1 - target iOS 10).
I have followed the steps reported...
