Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
In the documentation for the secure bootloader, it's mentioned that the provisioning data gets stored in OTP memory for some chips (e.g. nRF5340). Is there a way to know what...
Hi:
I don't receive any messages in the console during any of the exercises in Lesson 3 and Lesson 4 of the nRF Connect SDK Fundamentals.
No errors occurred during the...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hello,
I'd like to ask what needs to be configured to enable communication between two boards: nrF7002-DK and nRF5340-DK via another UART (e.g. UART1).
Please provide...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hi, I want to run Bluetooth Mesh Light example on nrf54h20 chip.
At the beginning I prepared devboard with this tutorial: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hi,
I'm new to nordic's product and new to study open mesh framework. But I have two questions:
Q1: what access address mean? Is it a parameter of mesh network ?does different...
Hey everyone, I'm trying to compile blinky example, using ARM on Mac OS X. I use st-link 2 to flash it. So, the first when I do 'make' command I've got errors
Makefile...
Gentlemen,
I apologize if this is not the correct place to post this question.
I have a potential project to start a BLE project but their requirement would be start...
I'm developing a new board with nRF8001, after reset i correctly get the DeviceStartedEvent 0x03 0x081 0x02 0x00, after that i go into setup mode sending the configuration...
Hi,
I am using nRF5_SDK_11.0.0_89a8197 at center to debug ble_app_uart_c project.
The center can connect the device well at the beginning. But if I power on and power off...
according to the introduction of mesh framework( value storage part), it says all mesh data is saved in a structure. My understanding is : Handle means a trickle instance...
How to configure S130 Softdevice as Completely Central(S120) i.e with Out Switching its mode to peripheral to operate like a central.
Is there any API or Example to do...
For example, if the first page is erased then it will set this page as swap page and continue looping without increasing the 'page' variable.
This means that the last...
Hi,
I have flashed boot loader to 0x7A000 (Size 24kb) and Softdevice to NRF52 DK ,then flashed application using nRF connect .
Am also able to update application after adding...
Hi,
I need PWM on 2 pins, with a varying duty cycle, and read some posts in this forum on the subject.
I am still using SDK7.2.0, with SD7. Our product is stable, so I...
Hello, a few days ago I was having trouble with RF performance on a custom PCB using the NRF51822. I posted here to get feedback and figure out where the design went wrong...
sdk : v8.1.0
os : ios
tool : nrf tool uart
use the ble_app_uart, it worked normaly. and add duf fuction in the application by the notice
[http://developer.nordicsemi...
Dear all
I found that the frontline BPA sniffer can't catch the connection data between Android5.1 or ISO and BLE device. Does this normal? How can I use the sniffer to...
Hello, I have to implement infrared sending and receiving of a modulated signal in pre-existing code.
I have managed to implement infrared sending thanks to the ble_app_uart_IR...
Hi!
I have creat two timer with app_timer_init.
start the first timer trigger every 4 ms, every 125 times(approximately 0.5 sec) to start the second timer which trigger...
