I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
I tried to add a dfu service to the SDK 11.0.0 ble_rscs_app by following the procedure here . I was able to successfully compile and run the application, and when Master Control...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hi all
We use the nRF51822 with the S130 V1.0.0 in the peripheral role and a Galaxy S5 in the central role. As soon as the S5 connects to the nRF, we send a connection...
Hello,
I have been working on a customised Nordic Board ,and I can't be able to do a DFU. The DFU App_dfu_dualbank doesn't display the DFUTarg Bluetooth profile on the board...
Yo man,
I use nRF52 with ADC fun in SDK11 and I want select ADC input to internal VCC.
I modify like below:
static nrf_drv_adc_channel_t m_channel_config = NRF_DRV_ADC_DEFAULT_CHANNEL...
Does the Bluetooth Peer Address of NRF51 Chips change randomly [every 15mins] or does it remain same?
When implementing whitelisting for secured connection, it is required...
Hi, I am unable to build this example in Keil Uvision5. I am getting following error:
"no source": Error: #5: cannot open source input file "......\main.c": No such file...
Hi,
I am trying to setup a testing environment using nrf51-ble-driver_win_0.5.0.
All of my job are:
Download nrf51-ble-driver_win_0.5.0, and program connectivity_115k2_with_s130_1...
Recently updated to SDK11 + s130 v2.0.1 on an nRF51822 xxAC LFCLKSRC=RC
BLE Advertising no longer works. Localized it to our use of TIMER2 for an implementation of systick...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...
Hi,
Everyone,
I am using NRF51422 chip for my custom board. with transmission interval set to 2000ms and Tx power to -20 dBm, I transmit 32 Bytes BLE data and Scan and...
