Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I'm trying to find out if drawing more than 70mA through the PPK will damage it.
As I have a beeper on my custom board that can draw 200mA, and I'm concerned that attaching...
I have 6 RGB LED strips and I would like to control them by Raspberry PI. 6 strips with 3 colors each require 18 controllable PWM sources, so I have SN3218 which is exactly...
Hi all,
I'm new to nRF51822 and I'm trying to use the fds system.
However, I always get a NO MEM return code when calling the init method.
Any hint?
Thanks
This is my code，the problem is when cpu executed the __WFI() instruct it should be paused ,this means that NRF_LOG_INFO("wake up\r\n") should not been executed only after...
I am trying to integrate an ADXL345 with my nRF52. I am attempting to implement Bjørn Spockeli's driver which I stumbled upon here: devzone.nordicsemi.com/.../
I am using...
Hi all,
I have an application for nRF52 which works fine using SDK 12.1.0. I am now trying to make it working with 12.2.0 and it hangs.
Apparently inside the function...
My question is somehow connected to hardware side of SPI(M) peripheral implementation.
When using SPIM, I am observing 3 types of situation:
WhenSCK pin is defined...
Hello,
I took this project on about a month ago to do bug fixes within the app. The bugs are fixed but the OTA was not tested for the last 2-3 months. No changes were made...
Hi,
I am working on interfacing SD card with nrf52. I am sampling SAADC at 1000 sps and trying to write over SD card as well as sending over BLE. Both operations are working...
Hi everyone,
I am trying to update my nrf52832 chip with another MCU using UART.
I am using the bootloader example dual_bank_serial_s132 with the s132 SoftDevice.
...
I plan on using the ISP130301 and would like to ask the following:
I would like to start my schematic and layout using the ISP130310 from Insight Sip and would like...
I'm wondering if it can be work as an DFU Controller (where sends zip Distribution Packet) not as an DFU Target.
I'm trying to make Each of the NRF51 Cores to be updated...
I am using the nRF52832 very successfully for an audio application. However, I am observing an undesirable high current state after audio playback is complete.
Here is...
Hello Everyone) Have new unsolved problem. My custom PCB based on nrf52832 SoC has only controller, FXOS8700 accelerometer and MAX30205 health temperature sensor. For communication...
I have been using SDK7.2 on an nrf51822 quite succesfully for a number of projects in the past.
However, for a new project, which is just a simple beacon, no complex IO or...
