Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am trying to port peer manager implemented in ble_app_gls to ble_app_uart using instructions in devzone.nordicsemi.com/.../ . I am using SDK_11 s130 on nRF51-dk.
I encountered...
hi all,
i am using SDK V8. i want to start and stop the RTC manually .i gone through rtc periheral example but still i am not getting . please help me. i am a beginneer...
Hello,
I am using the nRF51822 with SDK 10.0, S110 softdevice, and a SPI slave interface. The SPI slave interface works , but the standby power consumption of the nRF is...
Hi there,I am using s130, my device is now working at peripheral mode, it's advertising. I want to switch it into central mode by pressing a button. and switch back to peripheral...
If I had two devices, one set up as a peripheral and one as a central, what sort of factors do I need to consider to work out the lowest possible power consumption/average...
Hi,
I am sampling 2 200Hz signal using ADC and transmitting data using heart rate and battery service of ble_hrm(instead of using simulated data).
But since the connection...
I have the following setup:
nRF51 dongle
connectivity_115k2_with_s130_1.0.0.hex firmware
Windows 7 PC
nrf51-ble-driver_win_0.5.0
My app is written in...
Hi,
I see that you provide Master emulator API for windows (dll) that works with firmware for Master control panel application. Master control panel firmware, as the name...
Hello,
I try to set up an external signal for the LFCLK on a nrf52832. From this question :
I know the nrf52832 can do this (signal on XL1 pin, XL2 grounded).
...
Hello,
I am working on development to concurrent multiprotocol: BLE+2.4G proprietary. I am using timeslot feature in S132.
Because in my own 2.4g proprietary protocol, the...
I want to use feature reports in my HID project, but as far as I see this functionality is not fully included in ble_hids.c (SDK 11). I already managed to properly receive...
Hi,
I want to advertise in variable intervals and mostly only one advertisement at a time. I planned to do it like this:
1- start advertising with any interval (e.g...
Hello,
I followed the example for doing 128 bit UUID advertising using ble_app_uart example. The problem is, this seems to work if I run it when the radio and controller...
Hi,
I have my custom nRF51822 board based on Raytac MDBT40-P module. I am trying to program it with nRF51-DK(PCA10028). I could program it with mbed interface once or twice...
