Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi,
i am trying to wake up the nrf52832 from system off with a gpio interrupt.
When the signal on my gpio pin 28 goes from Hi to Lo, i trigger a callback function in...
Hello all,
I'm building a project on the nRF52382 with the S132 (v2.0.0-4.alpha). The project includes a Central device (GATT Clients) that read and write to 2 peripheral...
Are there any specs available regarding the performance of the nRF52 ADC's internal voltage reference? Accuracy (%) and temperature drift (ppm/degC) would be good. I couldn...
Hello,
I'm developing proprietary radio protocol using nRF52 (not using softdevice) and would like to know if it is allowed to write NRF_RADIO->FREQUENCY register while...
Hello, I've got a problem with an app_timer
starting from the BLE_UART example, I've set
#define APP_TIMER_PRESCALER 4
#define CLOCK_CONFIG_LF_SRC NRF_CLOCK_LF_SRC_Xtal...
Hi NordicSemiconductor's Community,
I have a basic question about the RAM and ROM management in Blogs section.
I don't understand this paragraph:
"The IRAM size consumption...
Iam using LPCOMP for my project i would like ot know where the header files are available to download, iam getting the error
....\main.c(33): error: #5: cannot open source...
Why isn't the nRF52 ADC internal reference voltage included in the electrical characteristics on the SAADC in the Product Specification? Knowing what voltage the ADC is referencing...
The table on:
infocenter.nordicsemi.com/.../gpio.html
specifies: Iol,hdh = max 15 mA for Vdd >= 2.7V.
The graph lower on the page (Figure 6. Max sink current vs Voltage...
Hi Nordic,
when 51822 communicate with an app,is the best way to use different services and characters
to achieve different passageway or use a self expand protocol on...
dear all
I have two same 51 822 device with same program, one is normal, the other can't be connected even re-power manually .The two all can be found by nrf master control...
Hi,
I have been able to use SAADC to measure temperature, but my code does not behave in the way I expect it to!
In the config file I have the following settings set:...
