hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello,
[Device: nRF18522 S110 Softdevice 8.0.0 SDK10]
I've referred to this post:
devzone.nordicsemi.com/.../
Does it mean the maximum value is 512 seconds...
hi,For the bluetooth certification, but requires a fixed frequency is 2402 2442 2480 test, could you tell me need how to set up 2442 under the fixed frequency?
I'm trying to make one of the examples in the SDK v9, but I'm stuck on the following error;
L:\NR - nRF firmware\Nordic SDK\V9\examples\ble_peripheral\ble_app_template...
Hi,
I use s110_6.0.0 and sdk_5.2.1 in my old product. I found that I can't write flash sometimes. Timer1 and Timer2 are used, and their interrupt priority level is 1(high_priority...
Hello,
I noticed that their was a question in the developer zone regarding MD bit?
devzone.nordicsemi.com/.../
My question is slightly different. I am using Soft...
Is it possible to use random 128-bit UUIDs for custom services and characteristics? Or do the characteristics in a service need to share 96-bits with the custom service UUID...
The hardware bug #39 on the GPIOTE in EVENT mode which gives a overconsumption of ~1mA even in idle mode on, kills the interest of having a low power chip, because the solution...
I am wondering, for 51422 or 51822, are all radios can work simultaneously or only one type of radio can work at a particular time?
e.g., BLE & ANT can work at the same...
Hi all,
Is it possible to get a callback from the softdevice, when a characteristic is changed? If so can you guide me in the right direction - documentation / examples...
@brief Function for application main entry.
*/
int main(void)
{
// Configure LED-pins as outputs.
LEDS_CONFIGURE(LEDS_MASK);
// Toggle LEDs.
while (true)
{
for...
Hi,
I'm using gazell library with app_pwm.
From documentation gazell use Timer2 and PPI channels 0,1,2.
APP_PWM use Timer0.
When I disable pwm using app_pwm_disable...
Hi,
I'm trying to use the nRF52832DK to flash a Rigado BMD-300 module (nRF52) - I've connected SWDIO, SWCLK, GND and voltage sense to P20.
It seems that because the...
I run the boardcast tx application on a nRF52832 board and I add uart drive into the proj. I use UART to console on PC.But uart doesn't work, PC console nothing. What's wrong...
I'm using the mouse example which use bonding and white list which allow to connect only to one central after performing the bonding
my question is, does the bonding feature...
Hello,
Is this the correct setup? What else will I need to do to make it work (e.g. it says something about the MCU will detect the external board and then programm/debug...
