I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm having problems with the I2C. For now what I see is the twi_transfer function remains in infinite loop. Other symtomp is the SDA line remains normally at low level...
Hello,
I am currently trying to transmit around 800kbps of data using the Nordic ESB protocol. I am also attempting to sample 2 inputs using the SAADC at around 32 khz...
Hi,
We try to communicate between nRF51822 SoC and a GPS module through UART on a custom board but failed initializing UART.
More details:
We use nRF51822 as a...
Hi i use a soft with DFU and Beacon.
I will use the beacon and when i press on a button i can update the software with DFU.
DFU and BEACON works independently but when i...
Hi. We are going to mass production now and the 3rd party lab that will certify our product says we need to have a special mode in the firmware that would do :
continuous...
Hello Nordic! Regarding Notifications on the s110, once sd_ble_gatts_hvx(conn_handle, ¶ms) returns NRF_SUCCESS , how long does it take, at most, in units of CI (Connection...
Dear sir.
I have question of SPI slave communication.
[NRF_SPIS1->TXDPTR] is a point to address of TX buffer.
After [spi_slave_buffers_set] is called and SPI transaction...
I've successfully compiled, flashed, and run the SDK11 ESB examples on nRF52 DKs using GCC, and am trying unsuccessfully to get them to work on the Keil 5.20 IDE.
I've...
I tried to get the ble_app_proximity example to work today, with either the nRF51-DK, nRF51-Dongle or nRF52-DK, along with the Nordic Connect app on Android.
I encounter...
I am working on application where the nrf51 will read information from several sensors and send the data to a smartphone app via BLE. Among the sensors are one that sends...
Hi, I am trying to get my ble400 board working with nRF51822 chip. I downloaded SDK v11 and made all nedded preparation. I have successfully compiled blinky app, and everything...
Hi Nordic Tech support team,
I'm Hardware design engineer and working on wearable IoT design and would like to implement OTA programming for nRF52832 Bluetooth SoC.Kindly...
this is my code:
this is BLE_peripheral UART and i added these lines to main():
my soft device is S130 V2 alpha
// Initialize.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE...
I'm working with the nRF8001, at present using the RedBear BLE Shield.
My current issue is that after starting to Advertise, but before a connection is made, I wish to...