But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I have recently started getting the following error during a DFU using MCP.
Capture.PNG
Any idea as to the cause of this? What is the best way to debug this?
I am...
Hi,
I am wondering why PSTORAGE_NUM_OF_PAGES is by default set to 2 in the DFU project.
From what I understand the pstorage_raw.c module is used to update bootloader...
In iOS, it is possible for different apps to send data to the same characteristics in the same device by calling retrieveConnectedPeriphrals… Is there a way to identify the...
Hello,
currently, I am trying to get the SPI (master with EasyDMA) to work. I interfaced it with an LED driver IC , which needs some signaling (via GPIO pins) along with...
Hi,
I'm using the nrf52 board with sdk11.
I want to know that i have 100 beacons and my nrf52 is a cenral.
1)How many beacons can scan by the central at a time?
2...
Hi, I have managed to get my nrf51822 DK kit to read LDR sensor values. However the characteristic values are represented as hex on the master control panel and also on the...
Hi,
I'm i'm sniffing the NRF51822 s110, using the Nordic's BLE sniffer (on s120).
The BLE device is in a connection, and do a connection parameter update to a new interval...
Hi All,
I'm trying to update the application firmware of an nRF52 board with OTA DFU.
I have managed to create a .zip package (under linx, gcc compiler, Nordic SDK11,...
I want to make a program for wireless accelerometer with a microcontroller "nrf51822". I prepared the code however I face a problem with the ".h" files such as "nrf_error...
Hi All,
I'm having trouble running one of my I2C sensors connected to the nrf52 when running at a 200hz sampling rate.
Interestingly enough, the same sensor seems to...
I mean what kind of header information and stuff besides the data. I could only find this for advertising packets.
A graphic or list like this would be nice:
byte 0...
Hello,
I'm currently working on profiling an embedded application on an nRF52 using the S132 SoftDevice.
I've found that the svcall sd_softdevice_enable takes approximately...
Hi,
My SDK version:9.0
SD:8.0
I use gpiote to generate an interrupt,
static void bma255_int_hook(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
g_int1_triggered...
My phone : Lenovo Phab
Problem : cannot pair with nRf 51822 from Bluetooth menu BUT when i use Official App ( NRF Utility etc) then connect and start receiving data " ...
Hi,
I am using nrf52 with sdk11.0, I have migrated the code of pwm_library code to ble_uart_peripheral.
But when i'm initializing the pwm the code it stops the advertising...
