Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hi,
I have been able to use SAADC to measure temperature, but my code does not behave in the way I expect it to!
In the config file I have the following settings set:...
Good day,
I try to add inline assembler like this:
asm("POP {R12,PC}");
but I have an error:
Error[Og006]: Error in inline assembly: "Error[401]: Operand syntax...
Hi!
I'm currently developing a driver to communicate with a sensor via I2C using the Nordic's nrf_drv_twi library. I based my code on the twi_sensor example, but since...
We are in process of identifying the right hardware for our project and considering nrf52832 as the core processor. For our requirements, we need to use external serial NOR...
Hi,
I was trying to complie my code but the Keil is giving this error, which I am pretty sure is about the recent update that I have downloaded. I am using nRF51822xxAA...
hi i am using nrf51 development kit. i have gone through nordic development zone tutorial to use Eclipse IDE. build was successful it is creating release folder in which i...
We are interfacing serial flash using SPI interface and use nordic nrf52 nrf_drv_spi.c as the library.
We have taken a look at nrf_drv_spi.c, and it seems in the api nrf_drv_spi_transfer...
I am using Nordic nRF51 Development Kit with SoftDevice_130_2.0.0.I tried to run the SDK 11.0.0's example "examples\ble_peripheral\ble_app_gls\pca10028\ser_s130_spi" from...
As Nordic newsletter, s132 v3.0.0 softDevice have been released, I have a question that: if I want to use new feature in s132 v3.0.0 like DLE or privacy, does Nordic need...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to know how to control the timeout from when the program goes from Bootloader...
My set Up:
TI as Peripheral,
Android as Central,
Nordic as Central
I am doing directed advertisement using TI as peripheral.
Using Andriod as central, I am successfully...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board.Using the OTA Tester (s210), I am currently doing an OTA Update with the s210 dual bank...
Hi all,
I have an STM32 connected to an nrf51822 via uart, and I want to do a firmware update of the stm via ble.
Therefore, I would like to take advantage of the Master...
