I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hey,
I have two nrf52 development board. One is PRX, one is PTX. I try to realize the scenario that:
PTX transmits a number like "100", PRX receives this data "100" and...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
For conventional Bluetooth, if two devices are connected, we can send and receive text/bytes to and from each other. It is generic since the two devices can be from different...
Hi,
I will just reiterate that question again.
I really need to get 32K RAM beacons, but Digi-key apparently has only 16K RAM or v.1.1.0 modules. Could advise where...
I read this post with great interest!
devzone.nordicsemi.com/.../
I'm having a similar problem with my Nordic Beacon application. I followed the advice to switch my...
I am using a nRF51822 to send data to an iOS device.
Because latency is critical to my application, i 've set up a test program that sends a packet every second , using notifications...
I have some questions about the scan response packet.
Can a scan response be sent with a peripheral that is configured to be connectable? IE not a beacon.
I read...
Dear Nordic Team,
Thanks for support.
I am using nRF5_SDK_11.0.0. How can i initialize the softdevice with internal RC oscillator in my source code. I am using the below...
Hello;
I'm trying to get data over the TX pin to be sent to the RX pin on a Raspberry Pi.
I have it working on several boards: The nrf51822 Development Board, the Redbear...
The radio notification tutorial ( devzone.nordicsemi.com/.../) says:
"The distance is the time window before/after the radio goes active. The radio events are radio_on...
I'm slightly bamboozled by the LFCLKCSRC options in the NRF52 datasheet / product specification.
Bit field SRC makes sense. Set to 0 for the internal RC oscillator, 1 for...
Hi
I am currently using the boot loader from SDK7.2.0, compiled using Keil.
However, for all the other software I am using GCC. But GCC support for the boot loader was...
Hi, i am trying to send my notify characteristic every 100 msec, i am using timer for this and when i am connecting to the nrf app, my nordic device is sending the data but...
Hello,
Thanks for your reading.
I tried to read the CHIP_ID value(0xD1) of BMI160 in MetaWearCPro firmware using SPI.
But I could not get the correct value(0xD1). The read...
