Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
I'm trying to add authentication with a key acquired Out-of-Band to a Peripheral BLE device in which I already have non-MITM bonding working. I'm using the Peer Manager module...
Hi ,
Am using NRF52 ,S132 SoftDevice
I have a simple Question, How can I know is any device already bonded or not to my peripheral ??
I need to show an option "Delete...
I am using nordic_sdk_10 with nrf51822 USB Dongle. I did a eraseall
flashed my softdevice and dfu bootloader and did a reset. Now i can see advertisement report DFU_Targ...
I am using a custom board with NRF51822-QFAC-R7 and Master Control panel on Android. The DFU is working with test images from SDK130.
BL : examples/dfu/bootloader/hex/dfu_dual_bank_ble_s130_pca10028...
Hi all,
I have been trying to get my Nordic nRF51822 transmit continuously on a particular channel for FCC certification. The Test lab wants me to test the product in 2402MHz...
Dear Forum Users,
I am trying to send the data in a burst. Thanks to this post I have managed to achieve ~2,5 kB/s. However this lasts only for few seconds. Then the stream...
When i load the example radio_test pca10040 in Keil i get the following error messages
Error #544: Required Software Pack 'ARM.CMSIS.4.5.0' is not installed
Error #544:...
Hello
I plan to use two Bluefruit LE Micro devices that contain the nrf51822 as BLE beacons.
I also plan to use a BLE receiver (on another arduino) to receive the beacons...
Hi,
I'm using GCC with SDK11 on linux. I'm able to build successfully. When I try to run "make flash" or "make flash_softdevice", I get error nrfjprog command not found...
I just got the nrf51822 evaluation kit. I followed the instruction and installed everything per instruction. When I tried to open “Blinky” project, I am getting the following...
Hello,
I have a peripheral based on the nrf52 that connects to my Android phone already in direct advertisement mode.
I am trying to get a NRF52 central working with...
Hello! I'm trying to use the PWM on a board containing an nRF51822 device. However, simply including the nrf_pwm.h file multiple errors are trigered, such as the following...
Hi everybody !
I try to use nrf52 DK with OSX
I follow this link
devzone.nordicsemi.com/.../
and I have a problem with this step :
launchpad.net/.../ download
...
hi,
i tried to make a ac dimmer circuit controlled with dc
i use nrf51822
this is my dimmer circuit
aaand this one is zero crossing detector
finally this...
