I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'm sorry for general question, but I need it for my calming down.
I'm delving step by step go throught header files into origin definition of function for understanding...
Hello,
I'm implementing bonding feature on nRF52 with SDK_0.9.2.
I found a tutorial which is devzone.nordicsemi.com/.../ .
I followed this tutorial and then tried to...
I have a sensor HTS221 that I would like to power from an nRF52832 I/O to allow programmatically resetting the sensor. Looking at section 20.4.1 GPIO Electrical Specification...
We have bots (what I'm calling our device for this question) that play both the peripheral and central role depending on their context (not unlike the relay example; except...
Hello,
I'm working with a nrf51822, SoftDevice S120 v2.0 and SDK v9.0 platform.
Specifically using it a Central role to connect to a Blood Pressure peripheral.
I...
HI,
Currently I try to run example/iot/tcp/client in nrf51 iot sdk on nrf51-dk board. Then on server side, I use "ping6" command to test the data sending and receiving...
Hi, Very happy to note that you are planning to release source for nRF Connect for Desktop soon. Do you have an updated timeline on that?
Also, I am trying to use pc-ble...
Noticed this for gcc with -0s optimization an application fail to save a bonding data. It is caused by byte alignment of
static uint8_t buffer_memory[(n_blocks) * (block_size...
Hello everybody,
I am a newbie, and I tried to follow this tutorial to set up my laptop for development.
Everything works until I went to the step "Import existing Eclipse...
Hi,
I am currently writing the firmware of one of our products that will be produced in mass market, and now my goal is to have a unique BLE device name for every sample...
I am trying to study the docs for GPIOTE in SDK12 and see various sections for GPIOTE. What are the differences between: Driver , Abstraction , Handler and Handling Library...
I'm following the tutorial Development with GCC and Eclipse
I could compile and flash existing project that attached to tutorial.
Now I can't understand what to to while...
Q1: how to do network commission? do we have to use an Apps to do commission linke CSRmesh? or it is already in a same network if we configure all nodes use the same access...