Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi All,
I am novice in this nordic nrf 51822 programming. I wanted to know the best way to do the
following.
I have two different functionalities to be run on eval...
Hi All,
In ble_app_hrs example two function is defined for gpiote_init()
1)
static void gpiote_init(void)
{
APP_GPIOTE_INIT(APP_GPIOTE_MAX_USERS);
}
2)
static void...
Hi
I found there is bonding managing routine in SDK HRM and Proximity examples.
bond_manager_init();
It means in these two case, after pairing with BTLE host, the...
My question is regarding the PPI channel groups. The documentation is extremely limited and leaves many questions.
My goal is to generate 3 PWM signals from a timer with...
If i understand tasks are for outputs and events are for inputs.
Wanted to know relationship between channel and the pin numbers. do they hold the relationship like...
Hello,
I am really confused on how to get a custom BLE service up and running. I have read through nAN-36, and compared the suggestions in that document to the HRS example...
In nRF51 reference manual v2.1 section 18.1.1, it mentioned that the RTC must be able to
run while the 16 MHz system clock (SysClk) source is OFF. 2 questions :
Q1: Since...
Hello,
I'm trying to get the SDK examples working in Eclipse. I have followed all steps(except debugging part) in the nan-29, but i can only import the s110/ble_hrs example...
I am looking for the spacing in mils or mm between the two samtec connectors on the nrfGO board. I am making my board to interface with the PCA10005/PCA10004 and I would like...
Hi,
I'm new to nRF8001 SDK and Bluetooth and I hope my questions are not too stupid lol. So here it goes:
I'm using the Nordic nRF8001 SDK to implement a self-defined...
Hi All,
i would like to know in ble_app_hrs example gpiote_init() is called from main
and then again called in led_start for what purpose it used in 2 place.
can...
I see that we can specify the SPI frequency in bps, I was just wondering how fast the SCK line was oscillating for these values. Does it use the 32.768 kHz crystal oscillator...
If the nRF51 chip is in System Off state, do the GPIO pins retain the pull-ups or pull-downs? If so, what value do they have and how much current can they sink or source?...
