Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hello,
There is a bug in pstorage.c from SDK which can cause that module to fail to complete a flash operation. The problem is that the pstorage_sys_evt_handler function...
The product spec says "This event will also be generated if the supply voltage is already below VPOF at the time the POF is enabled" but it seems like the event is not generated...
I have a BLE device that is using Nordic SDK 8.1 and uses PWM to control an LED. Now I want to turn the led off with PWM. To do this I set the duty cycle to 0 and printed...
Hi,
I'm working on nrf51822 with soft device s130. I'm trying to send a data packets from the nRF51822 over BLE to an android device.
I want to know how much data...
Hi!
I try to create a custom service. To do that I copied the ble_bas service and followed this guide.
You can see my init function here:
#define APP_UUID {{ 0xC0...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 as central and peripheral.
Q1. What's "sd_ble_uuid_vs_add" function? is it for setting service UUID?
Q2. If Q1 yes, how to change...
I was reading a review of this product from a 3th party and they was claiming that a disadvantage about using this chip is that "Some peripherals and resources are not available...
SDK: 13.0.0.0-1.alpha
example ： ble_app_hrs_freertos
I am developing a product, referring to the “ble_app_hrs_freertos” example, when I tested my functions found a serious...
I've just tried to update the mbed firmware on an nRF52-DK to version 0219, and have hit some problems. Firstly, after dragging the .bin file into the Bootloader drive, my...
I've had a sequene of problems attempting to install the power profiler software on my Lenovo T420 Win7 64 bit machine.
First Issue
When attempting to run the python_packages...
I would like to pick up audio signal with a microphone for ex. AKU340, then use audio codec to digitize it, then save the output in a SD card connected to the nrf52, reading...
Hi there! I am a beginner of bluetooth technology.
We try to build a kind of IoT based on bluetooth mesh nodes with nRF51822. According to the instruction of nRF Connect...
I've found out that softdevice S130 cannot handle the length longer than default MTU(23).
But I know L2CAP is responsible for assembling and disassembling packet.
So...
I'm using nrf51822 & S130 to read the temperature humidity values every 5 seconds from AM2301 sensor. For that I am using timer in system on sleep mode. The current consumption...
Thanks for all support so far.
One thing I want to ask that does your nordic Beacon chip can support Bluetooth 2,0 as well ?
I mean is it backward compatible
