Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
Hello team,
We have a problem here, we are running a new program with 5 years long-term standby IOT device, once we are trying to use SMS to configure the IOT device we...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
I'm using the beacon example (SDK 12.2.0) which I've modified slightly so that a sensor output initiates advertising for 20 seconds with LED1 flashing accordingly. I want...
Hello I was working with the Flash Storage examples in the nordic github repo. I noticed that the FDS example while it has a IAR Workspace it does not have the associated...
Hi,
I am having trouble with buttonless DFU on my application. I am working on custom hardware on the nRF51822, SDK10.0.0, S130.
When I enter DFU from my application...
I'm working with pca10028.
Then gpiote interrupt is triggered twice.
Why is this happening?
And what is BUTTONx_EXT connected to PCAL6408A(U7) in schematics?
Hi,
I am new to nordic development. I have programmed segger program softdevice by s110_nrf51_8.0.0_softdevice.hex and program bootloader by dfu_dual_bank_ble_s110_pca10028...
My project is to communicate with the AD7780 via SPI.
Nrf is the master and AD7780 is slave. I am know implementing my solution referring to an example i found about SPI...
I'm trying to make the nRF51422xxAC advertise. Using Segger Embedded Studio.
I have this code: bpaste.net/.../f29f74986c10
On line 109, I have a breakpoint. At that...
I've followed the tutorial about setting the eclipse environement devzone.nordicsemi.com/.../
I've got every thing to work except the debugging, it stops every time at ...
Hello,
I am trying to set the nRF52 to power off and wake up on a momentary button push (scope measures momentary push logic low around 50ms-100ms). However, I am struggling...
This is from the previous Blog: devzone.nordicsemi.com/.../
I've looked at the other dev boards. I found this one nRF52832 System on Chip and Amber SPP-over-BLE profile...
Hi,
I'm using the nrf52832 Nfc and I can't set a variable nfc message, the nfc message must be constant... In my case I'm trying to send a text via BLE and put it on the...
I found lots of macros in Makefile like below,but I did not found they were used in C or assemble file. I am cleanup my Makefile to remove unused macros... so could I remove...
I'm using a 51422 for a very short range, fixed system. I will never need the chip to receive or be received from more than 5 meters away, and more often just 2-3 meters....
Hi,
I own a Redbearlab BLE Nano with a nrf51822.
I want to use it to drive some WS2812 rgb LED (neopixels), using precised timings for bit-banging.
Before driving...
