Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hi I'm having the exact same issue found in this post:
I've only just started evaluating the board and haven't gone as far into measurements as that poster, but something...
I'm in the process of upgrading one of our applications from NCS 2.6.1 to 3.0.1. According to this document, the only versions of NCS that support modem firmware 2.0.1 and...
I 've been working with the nRF54L15 for a bit now and it' s been great, but trying to get a bit fancy now and running into problems. I 'm developing with the latest NCS v3...
Hi all, hope this is the right place. I'm developing a small breakout board to test/program the NRF52805; this board will eventually be expanded to include a pressure sensor...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello, I am developing my custom board using Thingy53 as a reference design. I am trying to achieve DFU from application using external flash for the secondary image and upload...
I'm getting Error 7 too few arguments to function 'lib_aci_set_local_data' C:\Users\nishant\Documents\Atmel Studio\6.2\ATmega_AdafruitLIB_nRF8001\ATmega_adafruitLIB_nRF8001...
Hello,
as far as I found out, a Peripheral that advertises will stop advertising as soon as it receives an incoming connection (BLE_GAP_EVT_CONNECTED). A central will however...
I'm using the nrf51822 with the IoT softdevice and SDK as an IPv6/6LoWPAN peripheral and Linux with a BLE dongle in the central role. Basically, I have everything working...
I'm trying to write 7 bytes (0x01 02 03 04 05 06 07) to my nrf51 Dongle with my own custom service running based on the Battery Service.
The problem is that I can only...
Why does it say that the nRF51822 has 1Mb/s and 2Mb/s data rates if it doesn't?
Quote from devzone: "6 * 20 B* 1/0.0075 s = 16 kB/s = 128 kbps".
And its only for S110...
Hi there
I am having problems with uart app on SDK V7.2
I have dowloaded Keil and all of the other demo's seem to be working but this one is not.
It will not connect...
Hi. i have a little problem.
For start, i want to use the referance Layout found here link text with the hardware description file of PCA10004.
So there is a simple method...
Previously, I used to load and debug my programs.
after a few months,
Today when I setup the environment again, now I can only compile and generate hex files from Keil....
Hi,
Now I am try to use sd_flash_page_erase() to erase a flash page.
Before I call it, I already stop all interrupt but I always get a error message "NRF_ERROR_NO_MEM...
Hello,
I am working with nRF51822 development kit (s130 softdevice). I want to use one software interrupt for my custom application. Is there any software interrupt available...
During my development with ANT protocol, I found that if you have a bunch of units all have one master channel. Channels will actually bump into other channels easily and...
Hi,
I'm trying to get the SPI Slave example working on my nRF51822 PCA100001 development kit.
SPI1_TWI1_IRQHandler never gets called even though the ACQUIRED and...
Looking into the schematics, I could not find any uart or spi signals on the connectors. I am good in soldering, but I would not dare connecting wires to the nrf51422... ...
