I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I am trying to keep nRF5340 in sleep state, and wake it up when there's a user input (e.g., button) and send a packet as fast as possible to iOS18. What would be the latency...
I have been following this tutorial by Nordic trying to install nrfConnect for VS Code, nRF Connect for VS Code, part 3: Building an application , but I am facing several...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I deleted all the mega camera stuff as I want the MCU read image from another stm32, I successfully...
Hello,
We are developing a system that have the nRF5340 as a part of several MCUs, and we want to be able to upgrade both cores.
According to this: DFU for the nRF5340...
Hello Everyone,
I am working on nRF51 can any one tell me how can i get current time in microsecond?
micros() return current microsecond time in arduino. I wants same...
I am new at this, I need to enable the OTA DFU mode on a nRF51822 QFAC chip on a pcb (the pcb has bluetooth).
how can I program it? what do I need to configure?
I am trying...
Hello,
I can't copy file from mail after updated nRF Toolbox to v4.0.4. (iPhone5s & iPhone 6Plus)
The app crashed when I select Copy to nRF Toolbox.
Any solutions?...
I found we have to build micro-ecc.lib on our own, so I follow the below link to start to build it:
Installing micro-ecc
Then, we meet the below to errors:
Makefile...
Im based in the example of SDK12.0 - MULTILINK_CENTRAL and i have to know the RRSI value in dbm if it is possible from the peripheral device that is connected to me but i...
nrf52 restart from main() after hit breakpoint and enter [Go] under IAR. It looks like there is some kind timer or watchdog to reset system etc... if stay in breakpoint (...
I have a PMIC in the device that I am building which will eventually take over from the battery. But I have to program the PMIC on startup, using the nRF52. I am trying to...
Hi,
It's the first time I'm developing a piece of code using Nordic SDK, so my question may be absolutely dumb!
We are working on a bl652 (with a nrf52 inside). I just...
I have an application that uses many TWI buses, on many pins of the nRF51. I handle this by initializing/uninitializing a single TWI bus for different transactions. I ran...
in S130 v2.0.0, what is address of central?
i'm using ble central tutorial successfully compiled.
in case of ble peripheral, i can set address whenever running.
so ble...
Dear Nordic Team,
Thanks for supporting.
How to add custom characteristics in standard service ?. I am using Health Thermometer service (HTS). I want to add two custom...
I mounted the chip onto my own PCB, I am not using a devkit, My board is "Wireless-Tag WT51822-S2", it is a module that uses nRF51822-QFAA as (SoC)
I am the ble_app_uart...
With the release of SDK 12.1 the Serialization of S130 is now deprecated.
Within SDK 12.0 the Serialization was supported NOT at all.
When this is true, I have to stay...
