Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
I am trying to setup a couple systems to use the Nordic rf sniffer. I have a pca10000, a pca10001 ver 2.0, a pca10001 ver 2.1 and a pca10031.
I loaded all with the rf sniffer...
Hello,
I am sending below setup packet to nRF8001, and i don't get any response form nRF8001. ACI as such works fine, i tried sending diff commands and able to receive...
Hello,
I am using Lenovo (late 2015 release) with android 4.4.4.
Got my nRF51822 Bluetoot Smart Beacon kit and downloaded the applications that are available on Playstore...
I have some very basic code that does not appear to be executing correctly.
There are two versions of code that I would think should have the same result. They do not,...
I am having trouble with setting priority of ADC_IRQn.
void ADC_init(void)
{
nrf_adc_config_t nrf_adc_config;
nrf_adc_config.reference = NRF_ADC_CONFIG_REF_VBG;
nrf_adc_config...
I'm using the nRF52-DK (SDK11.0.0+s132) and added in some example code from the RTC example (the RTC2 tick interrupt with prescaler=0 to toggle a GPIO) to the ble_hrs example...
Hi there!
I don't know much about FCC, UL, CE certification and want to learn. I am using the blend micro module which uses nrf8001 chip in my project. How do I get my...
Hi, i've just started to use the nRF8001, so forgive me if this is an obvious problem.
i'm using the nRF8001 with a microchip PIC processor.
i'm using the ace_tl_demo...
Hi,
I have read ANT Message protocol and Usage and tried to implement shared channel according to section 8.2. I am using nrf51422 and S210 and SDK 10.0.0
My master...
I'm trying to use TDD for my development of a BLE peripheral application, but I'm running into some problems. I'm using Ceedling, CMock, and Unity for my TDD environment,...
I'm trying to scan beacons. This is what I added to the example ble_app_uart_c :
case BLE_GAP_EVT_ADV_REPORT:
{
const ble_gap_evt_adv_report_t * p_adv_report = &p_gap_evt...
Hi all,
I have a problem in architecture of my application based on SD132v3 SDK12. It should interact with an iOS device as a peripheral and receive some data to display...
Hi,
I am using NRF51822 and SDK11 with S130. I have enabled WDT with 2000 as reload value as I'm using 1 second timer. But I want to immediately reset when a certain condition...
