When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
What exactly is block size in pstorage?
Desired block size for persistent memory storage, for example, if a module has a table with 10 entries, each entry is size 64...
I'm looking into using the CMSIS RTOS on the nRF51822 with the S110 softdevice which I've used successfully with other Cortex M0 MCUs. I realize the S110 isn't well tested...
Hello,
I am new to BLE shield and arduino stuff. I am working on a project where I have to send the sensor data i.e. temperature sensor, humidity sensor and pressure sensor...
Hi,
I'm using the nRF51822 and pCA10001 as SPI slave.
For reasons beyond my control I have to read the Rx Buffer before the CSN is released.
Yes, I know I shouldn´t do...
Hi!
Could I find somewhere (I was trying in Nordic docs and in previous posts but everything refers to previous versions of softdevice) how to perform bonding with key...
Hello,
When designing a 4 layer board with the nRF51822, should I connect the chip and impedance matching circuit to analog ground and keep the other digital chips isolated...
use nRF51822_Evaluation_Kit
I want to auto bonding by peripheral ,once peripheral connected with center(android app).
Is there have any API to send pairing request?
Hi, I tried uploading the example code from \nrf6310\spi_master_example to nRF51822 evaluation kit board, but no matter what I do, I always get SPI error. Not compile or upload...
Hi,
is there a nRF Master Control Panel equivalent App for iphone?
I'd need an app where I can set custom characteristic. The background is to update the device using...
I'm a begginer in embedded program. I have a mbed HRM 1017 that
is pin-compatible with Nordic PCA10004. .
I'd like to make a simple app to print out "Hello World" to terminal...
Hi guys,
How to update softdevice on mBED nRF51882 kit?
Details:
I have couple mbed dev kits with nrf51882.
I use Keil for development but will move to GCC after while...
Hello all,
I wanted to ask if there are any cad files for Eagle or other hobbyist level design tools for the nRF51 chips before I spend time to create and debug them? ...
hi guys,
I'm pretty new to nordic ble development, but I have a fair idea of the differences between EK, DK and the mbed enabled MKIT.
I'm trying to build a deploy about...
I have been following this post and pure-gcc to set up my eclipse environment in ubuntu 14.04. Thus far everything works well except i cant figure out why the softdevice is...
