I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Good times,
So I finally put in the tweak to enable the GPIO 9&10 pins to be used for GPIO instead of the default NFC mode. Must remember that reset for it to take effect...
Hello,
I'm testing ble_app_hrs example by nRF52832 DK.
When i change NRF_BLE_GATT_MAX_MTU_SIZE up to 158, the example project run properly.
But, when i change MTU...
Hello, I am using nrf52832 custom board, with SDK 11.0.0 and s132_nrf52_2.0.0 and trying to dim led. It seems the only suggested solution is to use the pwm driver. I was wondering...
Hello, im experimenting around with the nRF52 DK (and nRF51 DK also)
Now I have following setup on nRF52 DK:
SoftDevice: s132 nRF52 v2.0.1
Applicatoin: Example Project...
I have the option to connect nBLE51822 to MCU via SPI, UART or I2C. But is there any advantage of using SPI/ I2C interface over UART interface while connecting nBLE51822 to...
my code is below.
git_mpu9250_dmp.zip
Hello.
I use nRF52 & MPU9250.
I want to use DMP,
but I can't read data with DMP.
Because it have failed that writting firmware...
Hi there,
What is the recommended development tool setup for nRF52 Preview DK on Mac OSX?
Your guide for SDK 0.9.1 seem to rely on Keil which isn't natively available...
Hi all,
What is the difference between the app_mailbox and the nrf_queue api?
The documentation says:
A)
The mailbox library provides functions to safely exchange...
Hi team ,
I'm using sdk 12.1.0(E:\testing\examples\ble_central\ble_app_hrs_c\pca10028\s130) example.I want to change to this BLE_GAP_ADV_TYPE_ADV_NONCONN_IND in above example...
I'm using nRF52 + SDK11.0.0 + s132. I have a custom service (with a read characteristic and a separate notify characteristic). After adding the DFU service and uploading the...
Hi,
Following the docs I think I am able to write to flash but it will not read anything .
This is how I set it up, write and read :
static void sys_evt_dispatch(uint32_t...
Hi,
I used a PCA10040 dev kit with nrf52832 to test Serial Secure DFU Bootloader.
Followed all the steps in the example with my PC (Ubuntu 16.04.1 LTS 64-bit).
I...
I am using SDK 12.2.0 with soft device s132 3.0.0 using NRF52 Development Board(PCA10040).
I want to update Battery level to central device/APP.As i want to use code for...
Hi,
I am working with a nRF51822 chip placed on a Ble Nano v1.5 board and I would like the schematic of Ble Nano v1.5. Could anyone tell me where I can find the schematic...
