hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello
I have a problem with my code implementing BLE NUS peripheral. Program hangs in the function sd_softdevice_enable. I have tried with external oscillator and with internal...
My previous product uses an empty notification to indicate that a bulk transfer is finished. I attempted to send an empty notification but got error code 0x10 (NRF_ERROR_INVALID_FLAGS...
I'm using the pstorage driver on the nRF51 to maintain several NVM variables. The NVM functions correctly and maintains state between power cycles. However, when I reflash...
Hello to all Nordic jedi masters!
I am using the nRF52832 along with SDK v11.0
I want to have the SAADC generate events only when the converted value is above a certain...
Hi all,
I am using a nRF52-DK board to receive data from the USB port using Serial, and transmitting it using ESB to a second board. If I use either Serial or ESB individually...
The latest rev of the product spec (1.1 when this was posted) includes a table on page 77 that indicates that the System OFF draw depends on a wakeup source (e.g. GPIO, NFC...
while i open ble sniffer , it sucessfully recognizes the nrf51822 ble nano but when i press w to open the wireshark, it shows no packets and in the interface list it shows...
Example ble_app_uart compiled in Keil 5 O.K but the resultant HEX file in the build folder is only 34K whereas the hex file in the hex folder is 335k. I followed the tutorial...
Hi Nordic team,
Very impressive demo posted on the blog zone this week! I'm trying to understand the details and sorry if I ask something what would be visible in the source...
After upgrading to iOS 10, I have been unable to successfully interact with my device using the NUS. I used to use the NUS to communication with the device and retrieve stats...
Hi, my setup is:
nRF52 DK PCA1040 v1.0.1;
Adafruit MAX9814 electret microphone amplifier;
My project concerns about:
Sampling audio from the board with...
Hi,
I fix bug in original code and managed for nRF51822_xxAB. It is bootloader for application based on SDK7.This bootloader is buttonless and application start after 60s...
Hi all,
When using GCC and Eclipse with SDK 13.0.0 to program an nRF52832 with the Serial and ESB libraries, are there any limitations as to where you can put event handlers...
if i set the attr_md.vloc = BLE_GATTS_VLOC_STACK;
how to set the attr_char_value.p_value?
attr_md.read_perm = p_rrthermomter_init->rrthermomter_attr_md.read_perm;
attr_md...
