hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Can I use below code to send data packets continuously over nus (>20 packets)
i=UserUart.RxBuf[1]+2;
index = 0;
while(i>0)
{
if(i>20)
{
while((err_code = ble_nus_string_send...
Hi,
I am using nRF52 chip with SDK13.0. MTU size 155.
I am connect with device using android phone. After sending 1 byte command device starting to send continuous notification...
hello there i think i need two uart in my application. i read datasheet of both nrf51 and nrf52
in both there is only one uart.
can anyone have implemented software uart...
Use this routine E:\nordic\nRF5_SDK_12.2.0_f012efa3\examples\proprietary_rf\gzll\experimental\gzp_desktop_emulator
To modify the can communicate with PC nrf24luep pairing...
Hi.
I'm troubled.
I use nRF52 preview DK v0.9.0 & Keil5.
i tried ble_app_hrs_c in example folder of nRF52_SDK.
This program stopped at
err_code = sd_softdevice_enable...
Hello all,
I am actually implementing an SPI-master driver in non blocking mode, I write the following code, when I use a debeug led, the program enters well in the IRQ...
I started with the blu_app_template on a 52840. I have advertising working. I can see that from an iOS app. I can also see the details of the service. I see the characteristic...
I am using the Master Emulator C# examples to build my own application. None of the examples are able to properly connect to a remote device. When I open up the Master Control...
I'm writing an nRF52 DK btle application using SDK 12. The DK comunicates with 2 external peripheral via SPI and I2C interfaces. Complilation fails with the error:
._build...
hi, i am reading mpu6050 with nrf51822. every now and then the data got corrupt because of softDevice interrupts. if i don't use Softdevice the it runs perfectly but when...
Hi All,
I am using UART with baud rate 4800, with even parity and 1 stop bit. I'm getting 6-8 bytes in a packet. I'm receiving packets for every 8-10ms continuously. This...
I am attempting to use Unity + CMock onboard the nrf51 for unit testing. I have Unity working and can even output the results of unit tests using Segger RTT libraries. There...
When I try to install nrf5X command line tools in Windows 10, I get the error mentioned in the title, even though I am not doing installing any software in parallel.
Error...
I am attempting to use TIMER4 on an nRF53832 using SDK 12.2.0 but I seem to be running into some sort of granularity issue.
Specifically, if set up the timer with 16MHz...
I just received my new NRF52480 PDK, but it will not respond to any commands.
I tried nrfjprog -e -f nrf52 and this is the log output:
-----------------------------...
