I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hi,
i used the SPIM example to create a connection with my ads1256. on my breadboard it worked properly. now i switched to a layouted board and every SPI pin is working...
Hi all,
I am using a J link to program a NRF52 via keil. It is successful but, every second program it fails with a Flash timeout error.
I am programming the application...
Hi,
I am trying to secure DFU on SDK 11 (NRF52). Would you please suggest if there is a way to secure firmware on old sdk, without upgrading to sdk 12+?
Thanks.
Hi All,
At the moment, I have three nodes and would like to configure one node as an end-device and the other two as routers. Using CoAP, the simple_coap_server is used...
I am migrating from nrf51 to nrf52. Using SDK12.1
On NRF51, I used the PWM Library to use 2 buttons on the DK to dim up or down onboard LED1 (called OUTPUT_LED).
It worked...
We are attempting to perform an OTA and as such want to transfer a large amount of data as quickly as possible.
When I attempt to transfer the data with connection intervals...
Dear Nordic team,
We have been working with SDK 8 and Softdevice S110 so far. We would now like to have the DFU using OTA for our product. I am looking for SDK versions...
Hallo Community,
I am new with Nordic chips, now Im trying to develop a BLE central, then i took the BLE_CENTRAL BLE_APP_UART example to start doing it, the SDK is the...
hello,i am using nrf52 DK.I was testing ADC example code .I am giving acq time is 3microsec .I want to find the total time is taken to sample adc for one sec.In data sheet...
I used S130 peripheral nrf51822 - nRF5_SDK_12.1.0_0d23e2a
Master Console Panel connection ok, and bond click error - >
BTLE_CONNECTION_TIMEOUT
I debug in my application...
Hello,
I'm having trouble with my nRF52. The power consumption is around 2.17 mA when sleeping. I'm using the softdevice 4.0.2 enabled and using the sd_app_evt_wait and...
Hi,
I am testing the current comsumption of nRF52832 using the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon ".
The peak TX current I...
Hello,
I would like to know if I can use nRF51822 chip to get partial BLE packet information like Access Address, PDU before the whole packet has arrived.
If yes how and...
Long title, but basically sums it up - is there any way to put the nRF51 into the off state from within the hard-fault handler if the soft-device was enabled prior to the...
Hi guys, I am trying how figure out the the devzone.nordicsemi.com/.../ works or ecuations to estimate the battery life using a central module.
My central device is battery...
