I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Hi!
I may have found a bug/problem with nRF Connect v2.3.0.
I'm developing an BLE peripheral device based on nRF52832 and using nRF Connect (with PCA10040) as central...
I'm in the process of migrating from SDK 14.2.0 S140 5.0.0-2.alpha to SDK 15.0.0 with S140 6.0.0 on an nRF5280 based custom board.
It should be possible to do a secure DFU...
Hello!
During the development phase, we have been flashing our nRF52 devices directly (though the debugger) and with no signing keys. We have also tested flashing the...
I would like to use the COMP capabilities.
The input is from NRF_SAADC_INPUT_AIN1.
The input voltage is 0.1-0.8V.
I would like to get interrupt every time we change...
Hello everyone,
I use sdk14.2 softdevice S132. I want to write "uint8_t some_array [7] = {0x00,0x01,0x02,0x03,0x04,0x05,0x06};" with use fds_write and read the array from...
When using BLE_GATTS_VLOC_USER to store multi-word characteristic values that are updated by application code, what is the recommended way to prevent a partially updated value...
I am working with ble_app_uart code, in that I am trying to send continuous data over BLE. But the BLE getting disconnected while sending large data.
So I planned to have...
Hi,
We are using nrf51822 QFAAH00 with SDK 110 v8.1.0 in our project, the application will hangs or not work when control stuck at address 0x6b0 (sometimes at 0x640) programmer...
Hi all.
I've followed as much information i can find regarding RTT. I understand that it was build in to the SDK after 11 or so and I followed the guides on https://infocenter...
I use the connection event extension, but there are several concepts that I am not very clear.
Software:S132 v5.0 . SDK14.1.0 nRF52810
Goal: I need to use high throughput...
my TWI device sensor, both its writing and reading address is 0x55. This seems weird for library of nRF since the last bit should be set as 0 for transmission and 1 for receiving...
hi Engineers!
the questions - is it possible to implement multi advertising (need two) broadcasters with different advertising data use SD 140-6 (nRF52840) ?
in the new...
Our Project is based on the multiprotocol THREAD BLE dynamic example.
We have the BLE DFU also as part of our project and it is working.
We now need to add the flash storage...
Hello :)
I have a question about the timing of sending a bluetooth write request. I am using two nrf52 developement kits, one as master and one as slave. From my master...
