Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
I am developing a firmware and connected a spi LCD to nRF52840, but I got the max speed only 8 MHZ, in Datasheet is 32 MHZ max.
Which speed of the SPI master is max ? (I...
I'm getting a disconnect reason of 0x3D / BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE during a connection attempt. It does not happen for all my phones except one. It appears...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v15 and using keil mdk armv5.25 as a compiler. Currently I am trying to modify an example in the SDK...
Hi,
Quick question: I read in this article on the section "A tough world of lighting controls" it states the following: "Let's say that five messages are spaced 20 ms apart...
Hello everyone ,
We are able to read out ADC values(if i connect battery positive externally on ADC pins). i wanted to know if there is internal connection provided to any...
Hello,
Testing your nRF Connect with a BLE Thermometer. I was able to connect and read data.
Can you help me with one question I have ?
This is part of the log file...
Where to start? Is it possible?
I need to send data between the two chips using 802.15.4.
There is no need to form a network.
I was looking at the Wireless Uart example...
Hello all,
We want to run the example TCP-Client example from IOT SDK.
how should we proceed for the same ?
Which softdevice must we use ?
Thanks and Regards ...
Hi,
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit.
I am struggling to properly use FDS module. I am using multiperipheral...
Hi Support Team,
By testing SDK15.0.0/Serial DFU, I find that if we use non-default baud rate(115200), such as 9600 or 38400, we have to assign a non-zero value to -prn...
Hi everyone,
I have 2 boards that I've been using for testing. One is the NRF52 DK with the nrf52832 and the other is a simple custom board i made with an nrf52810.
I...
Hi all,
I'm currently making Mbed OS 5 able to work with the NRF51 with DFU enabled. It seems Mbed OS 5 currently has no support for a Nordic bootloader for the NRF51. Mbed...
Hi Guys,
I'm using SDK 15 Version and Nrf52832 DK.
now i want to use second uart when one uart is communicating with the PC Via CLI.
How Can i make it???
Thanks in...
Hello everybody,
I use NRF52832, sdk14.2, s132 softdevice. When I install SDK examples(for example nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c), the minimum...
