Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello,
I'm trying to make some current measurement using the nRF6707 and a nRF5 SDK Board(10040) (Board out of the box, shunts untouched).
We're facing problems measuring...
Hello,
Does the newest SoftDevice release v5.1.0 support the advertising data length extension (255 bytes)? If not, will it be available this year?
We are at the evaluation...
Hi,
I am using nRF52832 DK (PCA10040) SDK 14.2.0 and S132 V5.1.0.
I am planning to test the TWI loopback (in order to familiarise the APIs used for TWI in nRF52).
I...
Hello,
I want to update the connection parameters once the nrf52x (peripheral) is connected with the android (master). I tried the following:
In connection event i called...
Hi, Nordic.
I want to use BLE buttonless DFU sample application.
I tried to compile it using SEGGER Studio + clang, but compile error occurs as the below.
How can...
Hello, Everyone.
I have face some major issues.
First i explain the set-up of my project.
-> I have nrf51822 chip and connected to the external flash memory.
->...
Hi there,
I was trying to understand "sleep" power modes of the chip (CPU + Peripherals) in a bit more details - but my understanding is that everything is handled by the...
Hello guys,
these days i started to work with the CryptoCell library on nrf52840 and i'm facing some issues running AES CCM* mode
little example with pseudo code for initialization...
Hi there,
A little background in my experiences first: I've programmed a couple PIC24 microcontrollers in the past for VERY simple embedded system projects (i.e. making...
hi:
I am working with the nrf52832, and the radio transmitting data packet.I find the receive data is ok, but the crc indicate a data error. Why? This problem is same with...
Hey!
I'm working on a device which requires Bluetooth to be completely disabled for short periods of time. It's got a sensor in it that's sensitive to 2.4 GHz radiation...
Hello Nordic Guys,
We are working on the system based on BLE_APP_UART_C (central) and BLE_APP_UART (peripheral).
“Central” is always “ON” and scanning for the peripherals...
HI there,
I read somewhere here that the SPIM3 bus would be capable of 32MHz operations in the "next" chip revision (that was 6 months ago).
Could you confirm that it...
I have created a device that will connect and pair with one central. I would like it to re-connect automatically after disconnecting because it was out of range or turned...
I can connect/pair/bond to the nrfConnect app and disconnect then reconnect just fine. When I try to do the same to a central running on arm bluez 5.43, the second and subsequent...
