hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
What is the maximum sampling rate of nrf52832? I used the ppi on nrf52632 to collect the signal on gpio. After testing, it was found that when the signal on gpio is greater...
Hello all,
I want to built a coin cell powered thermometer with NTC thermistor.
May I know if I need to regulate the voltage from the coin cell or i can power the nrf52832...
I have a problem with the 802.15.4 software part of my nRF52840 PDK. I wanted to replace our current 802.15.4 hardware parts from TI with the new nRF52840, due to the lack...
Hello. We are now starting our review to customize code for the pending use of the Nordic devices in low power mode. Have a mix of Nordic kits now. Using the nRF52832 (PCA10040...
Hi,
I am trying to implement buttonless DFU by following the ble_app_hrs example provided in the SDK and modifying the bootloader (nRF51_SDK_10.0.0\examples\ble_peripheral...
We have our custom PCB design that we program and debug by connecting the SWD lines to nrf51 DK's SWD. We wanted to use trace for better debugging options, however we discovered...
Hi,
I have a task to do PWM frequency repeater on nrf52832. After reading forums I decided to make it with PPI, 2 GPIOTE and 3 Timers. Here what I did: https://github...
Hello everybody,
I used SDK14.2 S132
I defined fds_write and read function like that;
Also, I wrote a function to register particular data;
Then I used save_data...
Hi, I followed through this tutorial:
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
But to my frustration I realized...
Deer friends,
The nRF Connect BLE app supports the configuration of the local device's GATT attribute table, also known as server setup. Adding attributes to the server...
Hi
I am researching options for my bachelor project which happens to be about bluetooth 5, where I am looking to develop a smartlighting system using Bluetooth 5 mesh....
Hello Nordic Support!
We are making a prototype that connects the battery to Vcc, but 5 out of 10 It works properly. Conversely, the remaining five do not behave as expected...
Dear friends,
In the Power Profiling Application (an example of nordic SDK), the priority of the application timer is set to APP_LOW(as shown in the pic below).
However...
