As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi i'm going to do a school project with bluetooth mesh network so i was wondering if bluetooth 5 supports it and what are the benefits of using bluetooth 5 over bluetooth...
Hello All,
Can i use nRF52810 SOC for mesh networking. is there any space constraints?..
if we can use can we control all the nodes via smartphone .
please provide...
I am using nrf52832 peripheral and ble central with some android application .if an app opens it we get ble disconnect event and if we kill the app ble_disconect will come...
nRF52840 OPS 0.5.1 lists the following highlighted sensitivity spec:
The Bluetooth core spec defines sensitivity for this payload length as a BER of 0.017%, not 0.01...
Hi
We are trying a Nrf51-Dongle in a school prosject here in Norway We need to use one of the GPIO pins on the Nrf51-dongle as input When this input is 1 , we want the dongle...
Hi ,I am using nrf52 DK with mpu9255.I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in keil v5...
Using nrf51422 in KEIL. I am verrrryyyy new to this type of programming. I have been looking at multiple examples within the nortic github to find how to input analog reading...
I started Heart Rate Monitor app "ble_app_hrs_pca10040_s132" on nRF52 evaluation kit (nRF52832). Everything work well when I connect with nRF evaluation kit from Android devices...
Hi!
I just got my PCB with a Telit BlueMod+S42 Module on it (nRF52832).
I' using the LESC feature and ist works properly on the PCA1004 and on the Telit DevKit (same Module...
Hello,
I'm working on a bootloader based on the example of SDK13.1. I want to add two more characteristics to the DFU service, but after I add them, the nRF Connect app...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
