I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hello,
I configured pin P1.15 as output and with GPIO_PIN_CNF_DRIVE_H0H1 but I only get 1.7V ?
Does "standard drive" means that the pins can't get to 3V ?
Thank...
My project is based on the Thread cloud coap client example. I would like to know if my CoAP POSTs to the cloud are successful.
I added a "post_response_handler" to the...
Hi,
I've been trying to read/write data from/to the internal flash storage of my nRF52 development board.
I am using SDK11 and softdevice s132
I have modified the flashwrite...
Hi,
I've been trying to read/write data from/to the internal flash storage after a ble disconnect event occurs on my nRF52 development board.
I am using SDK11 and softdevice...
Hello,
i'm developing an interface based on nrf52. The app does a direct connection, performs some exchanges with the peripheral, and tells the peripheral to disconnect...
Hello we have a more stable external reference voltage source than the VBG for the ADC we want to use.
The voltage itself is higher than the allowed reference voltage specified...
Hi,
i am working on a project that in it i had developed a firmware for nrf51844 based on soft device 130 v2.0.1, now i decided to move the project on nrf52840 . i had read...
Hi! I did see a post about this, but is there a way to implement any kind of throttling/flow control over the Nordic UART service?
About the only thing I can imagine is...
Hi,
how can I publish a message to unicast address from a generic on/off client with mesh sdk?
How can I set the address?
Jost to be more precise, the function:...
After installing the USB driver for the nRF52840 dongle and using it successfully, and then connecting the nRF52832 DK it fails with "error occurred when opening port. Errcode...
Hi everyone,
I was trying to use QSPI interface with the on board external flash memory MX25R6435F on nrf52840 PDK
This is what i have observed, Inside the linker tab...
Hi, I have nRF51822 Board
Can I make it as a beacon kit?
what changes do I need to do to change that as a Beacon? any Source and Instructions are very helpful for me....
We need our PCB assembler to be able to program nrf51822 modules in situ. We have tracked the PCB to include a tag-connect footprint to this end. The assembly house will purchase...
Dear all,
I have an issue using USB bootloader for NRF24LU1+ device.
I've used a USB dongle and programmed USB bootloader to chip via SPI using external programmer.
...
Hello guys,
I have tried to get Nordic-Thingy52-mesh-demo working, but now I don't see it works according to description done.
I have followed all steps provided on...