Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Is there any tutorial or good example for I2C communication using TWI? I already saw the examples for TWI, but I don't find them very intuitive to change for I2C.
I'm trying...
After updating an application on nRF51822 chip with a new application which has new Characteristic UUID via BLE, iOS app cannot detect the new Characteristic UUID.
I know...
Hi to everyone,
I'm trying to use the CMD Mode of my Sniffer but I have different problems. First of all, when I switch to the CMD Mode the red LED didn't blink (it doesn...
`Hi Guys,
I have some sensor data of 20 bytes at each measurement at different period stored in EEPROM. Now i have to transmit all data over BLE continously.
example ...
I have a laser distance sensor module. I want to connect this module with my nRF52 DK(PCA10040). The module communicates over UART:
Supply (2.8V-3.2V VDC) connected...
I want to purchase a BLE development kit. My current preference is nRF51 because there are more nRF51422 BLE modules in the market.
www.nordicsemi.com/.../3rd-Party-Bluetooth...
hi,
I'm using ble central example using S130 softdevice . It works fine without editing anything. In my application, I dont want to put the nrf51822 to System On low power...
We are seeing random connections on our peripheral devices and we have tracked them to a Mac Pro. The computer has never been paired with any BLE devices so we have no idea...
hi
in this pic CODE_R1_BASE is 0x16000 and amount is 88kB
how its size in keil is 0x29000
if i calculate ram we have 8kB
8*1024 = 8192 that is in hex 0x2000 its...
How can I advertise a custom service and the Device Information Service?
I tried the following, but only my custom service is visible in the Nordic Master Control panel...
Hi there,
I'm issuing a STOPRX at a specific time but I'm noticing that more bytes are being put into the buffer from after the STOPRX was issued.
Is there a way to...
Since I've migrated to SDK 10 and updated all my toolchains I've noticed that when I debug on Eclipse, when I run my code nothing happens properly. However if I pause and...
There are various examples in the keil microvision examples for DTM.
The list is below. Is there a difference between these examples?
Which one should we use if our design...
Currently the default for the SPI0 chip select is active low. I would like to change it to active high. Can I do this?
If not can I just have the SPI chip select on a pin...
Continuing with my attempts to get this to work on SES I'm not sure if I'm missing something simple or not.
So using the excellent RKNRFGO (which by the way is much quicker...