Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hello,
I know that this question was here before, but I've read all of the questions and answers and still I don't know what I do wrong.
I'm using 3 PWM channels to...
Hi
While browsing the new files in the SDK 8.0.0 i had a look in the new ble_advertising module. In the start advertising function the pstorage access is checked if it's...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I have the nRF8001 plugged into the shield for the Arduino Uno.
From the Arduino SDK from Nordic, I have downloaded the BLE Hello World program to the Arduino, which should...
I know the SDK lists it for the S110 stack:
http://developer.nordicsemi.com/nRF51_SDK/doc/7.2.0/s110/html/a00066.html#app_dfu_intro_sec
But trying to use it with the...
There is a GitHub example:
https://github.com/NordicSemiconductor/nrf51-dfu-ble-S130
It states that the SDK 6.1 is required. Will it work with the 7.2 SDK using the...
I am trying to use TIMER1, but it seems that my ISR isn't being linked in during the build.
uint32_t timer1_init(void)
{
...
NVIC_SetPriority(TIMER1_IRQn, APP_IRQ_PRIORITY_LOW...
Hi,
I'm developing beacon-scanner software using nrf51822 and S120 softdevice.
Using softdevice v1.0.1.
I need to scan ibeacon type advertising devices and get service...
I am currently trying to come up with a viable strategy to log error codes that arise while my device is being used in the field. When an unexpected error code arises, I would...
Does someone use it?
The gls example from SDK 7.2.0 with softdevice 7.1.0 works.
However, the gls example from SDK 8.0.0 with softdevice 8.0.0 does not work.
I am using...
Hello, I'm new to bluetooth system.
I want to make some H/W device which using with sensor, MCU and Bluetooth.
Very simple, MCU control the sensor and get the data,...
Hello,
I have questions about DC/DC setup in nRF51822.
Is there any automatic switching between DC/DC enable and disable along with battery voltage except DCDCEN...
