Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
On nRF52, I see that 100 kHz gives a SCL period of 10 us which is correct but for 250 kHz, I get 8 us instead of expected 4 us. Similarly, for 400 kHz I only see 5 us instead...
I have a case where a module that can perform bit clears in the UICR needs to execute while a Soft Device is present and enabled.
I am aware that any direct flash access...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the soft device to work as s130 for its (simultaneous Central/Peripheral...
Hello!
I'm trying to read data off of a commercial blood pressure monitor (Qardio arm) using an nrf51822 with the nrf51 SDK v10.0.0 as the central role (s120). I am able...
Hi,
we are using nRF52832 and running into memory issues as we add functionality.
It would be great if the '40 was available as a drop in replacement in WLCSP package...
Hello.
I want RSSI check. so added source code as below.
test_rssi_start = sd_ble_gap_rssi_start(m_conn_handle,BLE_GAP_RSSI_THRESHOLD_INVALID,0x00);
if(test_rssi_start...
Hi all,
Is possible using NFC to send variable message? I want to send a counter event (data I got via BLE) to the NFC module.
Using the example I was not able to do...
Hey,
I'm just wondering how to add a UUID to the blinky example peripheral?
I want something like the heart rate sensor where its advertising BLE_Heart_rate_sensor.
I...
We have recently migrated from a custom board based on the nrf51 to a new board with the nrf52832. Our nrf51 board used to run at 6-8 uA when it was just sitting there advertising...
Hi
During schematic design, i read regarding proper powering of NRF52 (the product is battery powered 2xAAA). somehow i can't find this info now and i would like to verify...
What does mask and 1<< mean in the following code:
#define BSP_LED_0_MASK (1<<BSP_LED_0)
#define BSP_LED_1_MASK (1<<BSP_LED_1)
#define BSP_LED_2_MASK (1<<BSP_LED_2)
...
Hi all,
I'm transferring data to and from an Atmel AT25040 NVRAM using SPI, and it works perfectly when run within main(). However, if I run the same code from within an...
Hi, I want to enable notification for a specific characteristic, and to do that, I must write 0x01 (in java it's going to be "01,00" ) to the CCCD handle of this characteristic...
Hi,
I tried to use python API to drive the nrf sniffer to capture ble device information by their advertisement packet. I can successfully target a specific ble device...
